The Ford Barn

Brad in Germany · 09-07-2022, 11:33 PM

....or this French company, ADDA, made an entire series of different trailers specifically for the Ford Model A....like the Roadster pulling one of their enclosed trailers:

That is an excerpt from the original era ADDA flier.

Brad in Maryland

Brad in Germany · 09-08-2022, 12:07 AM

Digging deep in my archives, I think this might be what you are actually looking for......an original era Kraftfahrzeugbrief (voided) for a 1930 Ford "Personenwagen" (see block 1) (note the engine number, in block 3, starts with "A...." so it must be a passenger car, unless that prefix is not correct) and with block 12 indicating "Ist Anhängevorrichtung vorhanden? - Ja":

From the notes later on in the Kfz-Brief (and the corrections and hand written changes), it seems like this vehicle started out as a passenger car and in January 1938 was maybe converted to a LKW and in January 1945 was coverted to a "Generatorgas Antrieb".

mFG aus den USA,
Brad

Nick-Night · 09-08-2022, 01:23 AM

Hello Brad,

If you're the Brad I've heard so much about, then we have a friend in common and I hope you got back to America safely.

Thanks for the documentation, it helps me a lot. A car letter would of course be great. Unfortunately the attachment is not visible. Could you maybe send me the ADDA Prospect in a better quality? It is very difficult to read. From the weight of the trailer you could perhaps derive the towing weight. I'll send you a PM with my email address. Thanks greetings from cologne Sascha

//Edit
Unfortunately I can't send a PM yet
//Edit off

Nick-Night · 09-09-2022, 12:18 AM

I give up, yesterday I was at the TÜV with the documents from here. They need a data sheet from FORD where the trailer load is entered. Alternatively, this would have to be calculated by an engineer, which would be far too expensive. I was given the tip to contact a professor at the university to see if that could be a task for his students. But the whole thing blows the ramen for the benefit it brings. I want to thank you again for your help.

09-08-2022, 12:07 AM	#22
Brad in Germany Senior Member Join Date: May 2010 Location: Potomac, Maryland Posts: 1,131	Re: Looking for old trailer hitch documentation Digging deep in my archives, I think this might be what you are actually looking for......an original era Kraftfahrzeugbrief (voided) for a 1930 Ford "Personenwagen" (see block 1) (note the engine number, in block 3, starts with "A...." so it must be a passenger car, unless that prefix is not correct) and with block 12 indicating "Ist Anhängevorrichtung vorhanden? - Ja": From the notes later on in the Kfz-Brief (and the corrections and hand written changes), it seems like this vehicle started out as a passenger car and in January 1938 was maybe converted to a LKW and in January 1945 was coverted to a "Generatorgas Antrieb". mFG aus den USA, Brad Last edited by Brad in Germany; 09-08-2022 at 12:39 AM.

09-08-2022, 01:23 AM	#23
Nick-Night Junior Member Join Date: Jan 2021 Posts: 6	Re: Looking for old trailer hitch documentation Hello Brad, If you're the Brad I've heard so much about, then we have a friend in common and I hope you got back to America safely. Thanks for the documentation, it helps me a lot. A car letter would of course be great. Unfortunately the attachment is not visible. Could you maybe send me the ADDA Prospect in a better quality? It is very difficult to read. From the weight of the trailer you could perhaps derive the towing weight. I'll send you a PM with my email address. Thanks greetings from cologne Sascha //Edit Unfortunately I can't send a PM yet //Edit off Last edited by Nick-Night; 09-08-2022 at 01:30 AM.

09-09-2022, 12:18 AM	#24
Nick-Night Junior Member Join Date: Jan 2021 Posts: 6	Re: Looking for old trailer hitch documentation I give up, yesterday I was at the TÜV with the documents from here. They need a data sheet from FORD where the trailer load is entered. Alternatively, this would have to be calculated by an engineer, which would be far too expensive. I was given the tip to contact a professor at the university to see if that could be a task for his students. But the whole thing blows the ramen for the benefit it brings. I want to thank you again for your help.