|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
|
03-08-2012, 10:46 AM | #1 |
Member
Join Date: Aug 2011
Posts: 47
|
model a frame dimensions & identification
Can anyone tell the total length of a model a frame, Measured from the end of the frame rail to the end of the horns. Also how can you tell the difference between a 28/29 and a 30/31. Any help appreciated.
Thanks, Bob |
03-08-2012, 11:37 AM | #2 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,742
|
Re: model a frame dimensions & identification
The print I have is from WWW.wescottsauto.com
My puter's in terrible shape, I can't post anything or print out anything. However, I have a 103 1/2" wheel base. To which you add 10 I/2 for the horn and 1 5/8" (possibly 1 3/4" The picture isn't clear) for a total of 115 5/8 ". Warning, I have found this Dwg to be off on hole locations. Terry |
Sponsored Links (Register now to hide all advertisements) |
|
03-08-2012, 01:40 PM | #3 |
Member
Join Date: Aug 2011
Posts: 47
|
Re: model a frame dimensions & identification
Thanks Terry !
|
03-08-2012, 03:22 PM | #4 |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,552
|
Re: model a frame dimensions & identification
If generalities are all you are after, that print is fine but if you start looking closely you will see errors/
|
03-08-2012, 01:47 PM | #5 |
Senior Member
Join Date: May 2010
Location: Southern California
Posts: 7,063
|
Re: model a frame dimensions & identification
The difference between the '28-'29 and '30-'31 is brackets for certain bodies (slant window in '31 comes to mind) and the height for the radiator mounting pads is about 1/4 inch different. The early frames had a solid motor mount as part of the front cross member. Over the years some brackets went from stampings to forgings. The brake system changed . What are you trying to do, a driver or a show car (there is a big difference or a show car but you can work around most of the differences on a driver)?
Charlie Stephens |
03-08-2012, 02:21 PM | #6 | |
BANNED
Join Date: May 2010
Location: Walla Walla, Washington USA
Posts: 6,066
|
Re: model a frame dimensions & identification
Sponsored Links (Register now to hide all advertisements)
Quote:
Then go to the article I did for MAFCA some time back...this will give yiou a good idea about Model A Frames with photos. Pluck |
|
03-08-2012, 02:54 PM | #7 |
Member
Join Date: Aug 2011
Posts: 47
|
Re: model a frame dimensions & identification
Hi Charlie-
Just trying to ID the frame I have. If i use it, it would be a driver. |
03-08-2012, 04:12 PM | #8 |
Senior Member
Join Date: May 2010
Location: Southern California
Posts: 7,063
|
Re: model a frame dimensions & identification
|
03-08-2012, 05:33 PM | #9 |
Member
Join Date: Aug 2011
Posts: 47
|
Re: model a frame dimensions & identification
I have looked for the serial number but will look closer tomorrow.
|
03-09-2012, 10:25 AM | #10 |
BANNED
Join Date: May 2010
Location: Walla Walla, Washington USA
Posts: 6,066
|
Re: model a frame dimensions & identification
Can anyone help Bob out here? Anyone with a frame that you and him can corresponed with?
Thanks. Pluck |
03-08-2012, 02:56 PM | #11 |
Member
Join Date: Aug 2011
Posts: 47
|
Re: model a frame dimensions & identification
Thanks Pluck will do.
Best, Bob |
03-09-2012, 05:03 PM | #12 |
Senior Member
Join Date: May 2010
Posts: 1,670
|
Re: model a frame dimensions & identification
Here's another frame dimensional diagram that I saved from somewhere - I've hardly looked at it, so can't comment on the accuracy of the shown dimensions.
|
03-09-2012, 08:04 PM | #13 |
Senior Member
Join Date: May 2010
Posts: 1,264
|
Re: model a frame dimensions & identification
Is there anyone that has a drawing like the one that Randy in Ca submitted for a 1930/31 frame. I assume these two frame dimensions are the same although very different than 28/29.
Thanks for your time and any help. Cape Codder |
03-09-2012, 09:07 PM | #14 | |
BANNED
Join Date: May 2010
Location: Walla Walla, Washington USA
Posts: 6,066
|
Re: model a frame dimensions & identification
Quote:
BUT...I think it also pertains to the 1929 also as far as measurments go. Pluck |
|
03-29-2016, 11:59 AM | #15 |
Senior Member
Join Date: May 2010
Location: Fresno, Ca.
Posts: 3,636
|
Re: model a frame dimensions & identification
|
03-29-2016, 09:07 PM | #16 |
Senior Member
Join Date: Jan 2015
Location: Birkdale, Qld,Aust
Posts: 170
|
Re: model a frame dimensions & identification
|
03-30-2016, 09:34 AM | #17 | |
Senior Member
Join Date: May 2010
Location: Fresno, Ca.
Posts: 3,636
|
Re: model a frame dimensions & identification
Quote:
1. Get the Ford frame dimensions (print) for the locations.. 2. Measure a known/good/ correct frame... |
|
05-04-2016, 09:56 AM | #18 | |
Senior Member
Join Date: May 2010
Location: Fresno, Ca.
Posts: 3,636
|
Re: model a frame dimensions & identification
Quote:
I checked a GOOD, known frame that is flat, and measures GOOD for "diamond". Most all of the measurements fore and aft are not even close, the measurements left too right look close. So I don't consider this print good for checking a frame... I'd like to find a Ford print,...anybody have one? http://www.fordbarn.com/forum/showth...sion&showall=1 |
|
03-18-2012, 04:01 PM | #19 |
Member
Join Date: Sep 2010
Location: Phoenix/Mesa AZ
Posts: 44
|
Re: model a frame dimensions & identification
Randy / Cape / Steve - actually, everyone. Randy's drawing is the Wescott drawing (Wescottauto.com). While a lot of us appreciate having it avaialble, it seems to me there are errors and omissions. Ex: the 23-1/4" dimension at the bottom of the rear section doesn't add up. Add the distances between fittings from the same baseline and you get 22-1/8". There's another version of the drawing that has the front cross member in section view that I kind of have a hard spot with, too.
Anyway, I couldn't find a complete dimensional print for my frame (1929) so I started a CAD drawing, but don't want to use my 80+ year old frame as a reference. I'd like to locate bolt holes, sizes, rivets, etc. If anybody knows where it's already been done, that would be great and save me some effort. Otherwise, if anybody be interested in reviewing and giving me input, I'd be happy to post a complete print of the frame on the boards when it's done. Sorry for hijacking the thread. |
03-18-2012, 06:14 PM | #20 |
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,393
|
Re: model a frame dimensions & identification
Please post it when you're done.
Paul in CT |
|
|
Sponsored Links (Register now to hide all advertisements) |
|