Forum: Early V8 (1932-53)
04-14-2024, 10:29 PM
|
Replies: 11
Views: 871
|
Forum: Early V8 (1932-53)
04-14-2024, 10:26 PM
|
Replies: 6
Views: 395
Re: Frame vin
I use white chaulk, then wipe off frame. Chaulk stays in numbers-had to teach the DMV this trick. Newc
|
Forum: Early V8 (1932-53)
04-12-2024, 04:42 PM
|
Replies: 2
Views: 258
Re: 34 Pickup hood
NO; the side hinges are each 1/4" separate rods. The center hinge is part of one side of the hood. It's a pain, cause only one side at a time should be raised to service the engine. Only 33/34...
|
Forum: Early V8 (1932-53)
04-12-2024, 12:36 PM
|
Replies: 54
Views: 2,379
|
Forum: Early V8 (1932-53)
04-11-2024, 08:57 PM
|
Replies: 15
Views: 909
|
Forum: Early V8 (1932-53)
04-10-2024, 11:05 PM
|
Replies: 3
Views: 276
Re: Blitz
My 'Blitz' problem is the wiring. '42 F30 cab 13 style. Newc
|
Forum: Early V8 (1932-53)
04-10-2024, 11:26 AM
|
Replies: 18
Views: 896
|
Forum: Early V8 (1932-53)
04-09-2024, 10:56 PM
|
Replies: 18
Views: 896
Re: Annual MONSTER Swap Portland, Or
I worked the 'Parts Pickup' Friday PM. Constant full loads going out on 'OUT of State' vehicles! Lots of Idaho, Washington and British Columbia vehicles. Newc
|
Forum: Early V8 (1932-53)
04-08-2024, 10:28 AM
|
Replies: 3
Views: 343
|
Forum: Early V8 (1932-53)
04-08-2024, 10:26 AM
|
Replies: 18
Views: 1,158
Re: Skip Haney
Frequent problem in this 'hobby', NO apprentists to take over. Newc
|
Forum: Early V8 (1932-53)
04-07-2024, 11:25 AM
|
Replies: 13
Views: 980
|
Forum: Early V8 (1932-53)
04-06-2024, 08:18 PM
|
Replies: 1
Views: 141
33/34 Commercial Dash light fixture and switch
Scrounged up the original set-up. Not very complicated, the light bracket is grounded by the center dash screw. No 'D' nut in the body- 'D'[swedged cage ] nut is in the light bracket, which goes...
|
Forum: Early V8 (1932-53)
04-06-2024, 08:07 PM
|
Replies: 6
Views: 289
|
Forum: Early V8 (1932-53)
04-04-2024, 08:45 PM
|
Replies: 18
Views: 896
|
Forum: Early V8 (1932-53)
04-04-2024, 08:42 PM
|
Replies: 5
Views: 298
Re: Floor board clinch nuts
antique hardware stores have them. My Dad's old cans are full of them. antique furniture also uses them. Newc
|
Forum: Early V8 (1932-53)
03-31-2024, 10:48 AM
|
Replies: 19
Views: 1,116
|
Forum: Early V8 (1932-53)
03-30-2024, 02:50 PM
|
Replies: 11
Views: 340
|
Forum: Early V8 (1932-53)
03-29-2024, 09:13 PM
|
Replies: 4
Views: 333
|
Forum: Early V8 (1932-53)
03-28-2024, 08:17 PM
|
Replies: 1
Views: 202
|
Forum: Early V8 (1932-53)
03-28-2024, 08:16 PM
|
Replies: 15
Views: 784
|
Forum: Early V8 (1932-53)
03-28-2024, 12:18 PM
|
Replies: 1
Views: 202
'34 Commercial photos in V8 book
Found some good '34 Commercial Cab interior photos in the Old 33/34 restoration guide book. Pages 7/17 ;6/16 maybe more? Good commercial photos are needed. Newc
|
Forum: Early V8 (1932-53)
03-28-2024, 11:40 AM
|
Replies: 7
Views: 691
|
Forum: Early V8 (1932-53)
03-27-2024, 10:07 PM
|
Replies: 21
Views: 910
Re: rear drum studs
Fit by bolt circle is the same, But the studs can be tooo short for some wheels. My forty with post war 15" had only half the threads used in the lug nuts. Newc
|
Forum: Early V8 (1932-53)
03-27-2024, 05:23 PM
|
Replies: 21
Views: 910
Re: rear drum studs
There are Wheel differences as to lug holes ! Innies vs outies, pre war vs post war. If lug nut only uses half of its threads, you will see the difference in length. Newc
|
Forum: Early V8 (1932-53)
03-26-2024, 11:16 AM
|
Replies: 12
Views: 928
|