Forum: Model-A
12-31-2011, 06:25 PM
|
Replies: 43
Views: 9,793
|
Forum: Model-A
12-26-2011, 09:35 PM
|
Replies: 7
Views: 3,398
|
Forum: Model-T
06-07-2011, 04:16 PM
|
Replies: 0
Views: 1,199
|
Forum: Model A (1928-31)
03-21-2011, 03:38 PM
|
Replies: 71
Views: 46,122
Re: speed parts on the banger
every one else has idea's now i am going to take a turn: i have a 29 ccpu, with all the "neat" go fast stuff, have spent a TON of $$ in doing all the mods, that have been addressed, including the...
|
Forum: Model A (1928-31)
03-20-2011, 08:35 AM
|
Replies: 29
Views: 7,237
|
Forum: Model-A
03-15-2011, 07:38 AM
|
Replies: 1
Views: 835
wanted to buy
would like to buy a trippe speedlight for parts. (need the crown piece) what might you have? thanks for looking
|
Forum: Model-A
03-12-2011, 08:13 AM
|
Replies: 0
Views: 1,104
trippe speed light
found a trippe speedlight at a swap meet, the crown is missing (level). anyone have an extra laying around that needs a good home?
thanks b.j.
|
Forum: Model A (1928-31)
02-21-2011, 07:41 PM
|
Replies: 21
Views: 5,279
Re: Screws and my vocabulary.......
a roll of quarters, call those fastners name that they really are, throw a fit, repeat UGLY words, won't help, sure make you feel better :rolleyes:
|
Forum: Model-T
02-19-2011, 01:47 PM
|
Replies: 6
Views: 1,915
Re: Chikashay swap
james, i have a few of both: long way to haul, (from jacksonville, fla)what are you paying for good flywheels; have some t with magnets installed, coil rings, crankshafts, both t and a, maybe a...
|
Forum: Model-A
02-15-2011, 06:40 PM
|
Replies: 0
Views: 976
1929 ccpu
1929 ccpu: BANGER all steel: engine bored .100,1.7 valves, stipe roadrunner cam, lion head, crager side cover,2 stromber 81 carbs/ electronic ignition, balanced. 53 ford flywheel, small clutch,reds...
|
Forum: Model-A
02-15-2011, 06:15 PM
|
Replies: 0
Views: 990
1931 ccpu narrow bed
1931 indented ccpu with narrow bed: new fenders/running boards/splash panels. the frame and running gear all have been either rebuilt or restored. has mitchell o/d. all the prior has been painted,...
|
Forum: Model-T
02-15-2011, 06:04 PM
|
Replies: 0
Views: 1,358
1914 touring car
`1914 touring, ground up restored: new fenders/running boards/splash panels/brass works radiator/new top/new interior/new wood kit installed/gas generator/ coils rebuilt by coilman/engine, trans,...
|
Forum: Model A (1928-31)
02-02-2011, 07:44 AM
|
Replies: 30
Views: 13,085
|
Forum: Model-A
01-17-2011, 08:46 AM
|
Replies: 4
Views: 1,205
|
Forum: Model-A
01-12-2011, 08:49 PM
|
Replies: 4
Views: 1,205
wanted to buy
rear main bearing cap (one or more) 30-31 with 3/8 drain tube-going to try to install inserts in my model a: need one to practice with and one to mess up:mad:
|
Forum: Model-T
01-04-2011, 07:31 PM
|
Replies: 0
Views: 1,180
wanted to buy
set of top irons for a 1913 run-a-bout: no junk please.. :cool:
|
Forum: Model T (1909-1927)
12-22-2010, 05:03 PM
|
Replies: 2
Views: 1,518
Re: needed parts: any idea where?
thanks MTM called mark took very good care of me....forgot about him, haven't seen his adds in a long time in the vintage mag. Merry Christmas b.j.c.
|
Forum: Model T (1909-1927)
12-22-2010, 01:25 PM
|
Replies: 2
Views: 1,518
needed parts: any idea where?
i need a set of top irons for a 13 runabout also a gas generator for same. have tried the swap route with no luck, so i'm going to by new (repops).looking for good vendor,any suggestions?
Merry...
|
Forum: Model T (1909-1927)
12-11-2010, 04:59 PM
|
Replies: 1
Views: 1,495
tubes
i have been snake bitten with metal stem 30X3 1/2 inner tubes: i have 4 to split in the middle, yes they were stored with some air installed in a cool, dark, safe place, lovingly stroked each time i...
|
Forum: Model A (1928-31)
12-08-2010, 08:42 PM
|
Replies: 2
Views: 1,303
Re: Loose Oil Pump?
i would not worry too much about the pump being loose. i would be more worried about the pin (?) being too tight. i had a customers whose pump broke from a bolt being installed to keep the pump in...
|
Forum: Model A (1928-31)
11-24-2010, 07:27 AM
|
Replies: 14
Views: 2,612
|
Forum: Model A (1928-31)
11-20-2010, 08:33 AM
|
Replies: 17
Views: 3,865
Re: Gas Tank Sealer deterioration
thinking outside of the box: this is not my idea, one i heard a while back, instead of using rocks, bb's, chains, and most any other thing you can get into the tank. why not use glass?
break up...
|
Forum: Model-T
11-11-2010, 01:28 PM
|
Replies: 0
Views: 1,544
wanted to buy
need a set of brass spark/gas rods for a 1913, seems like all the parts houses are out of stock:
thanks for your time.
b.j. cannon
|
Forum: Model A (1928-31)
11-08-2010, 06:42 PM
|
Replies: 16
Views: 13,513
Re: Lightening Model A Ford Flywheel
make that engine "sing": install a 53 ford flywheel/clutch/pressure plate weighs about 32 lbs. have done this myself, for me it has worked great.
|
Forum: Model-T
10-20-2010, 03:47 PM
|
Replies: 0
Views: 1,484
lizard head
new never installed: don't know any more, bought at an estate sale. $300 + shipping.
|