The Ford Barn
FordBarn.com
The Forum
Swap
About
Register
Calendar
Community
Today's Posts
Search
FAQ
The Ford Barn
>
Search Forums
Search Results
User Name
Remember Me?
Password
Community Links
Members List
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Sponsored Links (Register now to hide all advertisements)
Showing results 1 to 11 of 11
Search took
0.00
seconds.
Search:
Posts Made By:
Club Coupe
Forum:
Early V8 (1932-53)
04-01-2021, 07:42 AM
Replies:
6
shifts hard
Views:
951
Posted By
Club Coupe
Re: shifts hard
Thanks to all of you for your replies. I'll start removing all the small parts tomorrow and clean and lubricate them before reassembly. I would start today but it's that time of year for my first...
Forum:
Early V8 (1932-53)
03-31-2021, 04:38 PM
Replies:
6
shifts hard
Views:
951
Posted By
Club Coupe
Re: shifts hard
Thanks, Bob. Looks like I need to pull the entire steering column out. Rats!
Forum:
Early V8 (1932-53)
03-31-2021, 03:57 PM
Replies:
6
shifts hard
Views:
951
Posted By
Club Coupe
shifts hard
1950 Club Coupe. Shifting from first to second I raise the shift arm up to neutral and the spring does not pull the lever down to go on into second. I must push it forward then on into second It has...
Forum:
Early V8 (1932-53)
10-21-2020, 07:46 PM
Replies:
3
knob on choke cable
Views:
813
Posted By
Club Coupe
Re: knob on choke cable
Thank you both. I plan to reuse the know so I will try that tomorrow.
Forum:
Early V8 (1932-53)
10-21-2020, 04:40 PM
Replies:
3
knob on choke cable
Views:
813
Posted By
Club Coupe
knob on choke cable
I have a bad choke cable on my 1950 Ford. I can't get the old knob off. I tried screwing it off and pulling it straight off but nothing gives. What am I doing wrong? Can one of you advise me?
Forum:
Early V8 (1932-53)
01-04-2020, 06:51 PM
Replies:
4
Dtill a hole in the floor?
Views:
1,313
Posted By
Club Coupe
Re: Drill a hole in the floor?
Thanks, 40cpe. At least I will know the hole's in the right place.
Forum:
Early V8 (1932-53)
01-04-2020, 06:38 PM
Replies:
4
Dtill a hole in the floor?
Views:
1,313
Posted By
Club Coupe
Dtill a hole in the floor?
I am considering installing an OD tranny in my 1950 Ford. I have been offered one for $700which has been pro rebuilt. After doing some reading and Youtubing it looks like (among several other things)...
Forum:
Model A (1928-31)
01-04-2020, 05:40 PM
Replies:
3
a hole in my floorboard??!!
Views:
1,464
Posted By
Club Coupe
a hole in my floorboard??!!
I am considering putting an OD tranny in my 1950 Ford. I have a rebuilt one available for $700. After reading and watching YouTube videos it seems that (among other things) I will need to drill a...
Forum:
Questions & Suggestions
01-04-2020, 02:24 PM
Replies:
1
A hole in my floorboard???
Views:
1,274
Posted By
Club Coupe
A hole in my floorboard???
I am considering installing an OD tranny in my '50 club coupe. I have been offered a rebuilt one for $700. After doing a little research, it looks like I may have to drill a hole in my floorboard for...
Forum:
Early V8 (1932-53)
11-23-2019, 09:20 PM
Replies:
14
gear ratio
Views:
2,508
Posted By
Club Coupe
Re: gear ratio
Thanks, friends. I'm sure this will not work in my '50. I just wondered what car had a gearing that high. I would have to get a push to take off even if it did fit. But I will tell the owner of the...
Forum:
Early V8 (1932-53)
11-22-2019, 01:00 PM
Replies:
14
gear ratio
Views:
2,508
Posted By
Club Coupe
gear ratio
An acquaintance is trying to give me a differential for my 1950 Ford. It has 15 teeth on the pinion and 42 on the ring gear.
By my calculations that is a 2.80 ratio. Obviously I can't use it but I...
Showing results 1 to 11 of 11
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General Discussion
Model T (1909-1927)
Model A (1928-31)
Early V8 (1932-53)
Late V8 (1954+)
Hot Rods & Customs
The Swap Meet
For Sale
Model-T
Model-A
Early V8
Late V8
The Jalopy Auction House
To The Editors
Questions & Suggestions
The Test Forum
The Archives
Model-T
Model-A
Early V8
Late V8
Sponsored Links (Register now to hide all advertisements)
All times are GMT -5. The time now is
02:50 PM
.