Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 303
Search took 0.02 seconds.
Search: Posts Made By: tinkirk
Forum: Model A (1928-31) Today, 02:10 PM
Replies: 17
Views: 238
Posted By tinkirk
Re: Should I be worried about any of these noises?

Almost sounds like a very bad vacuum leak
Replace exhaust intake gaskets and try it again


Sent from my iPhone using Tapatalk
Forum: Model A (1928-31) Yesterday, 04:56 PM
Replies: 8
Views: 433
Posted By tinkirk
Re: Unhappy with pressurised radiator

Do you have an expansion tank hooked up


Sent from my iPhone using Tapatalk
Forum: Model A (1928-31) 06-17-2021, 12:34 PM
Replies: 83
Views: 2,869
Posted By tinkirk
Re: I'm not a Model A person

it's defiantly a learning process but you will learn it just don't give up because they are nice to drive and enjoy the country side

good luck
Forum: Model A (1928-31) 06-17-2021, 11:05 AM
Replies: 83
Views: 2,869
Posted By tinkirk
Re: I'm not a Model A person

just drive it and enjoy it
Forum: Model A (1928-31) 06-15-2021, 01:51 PM
Replies: 26
Views: 1,621
Posted By tinkirk
Re: Andalusite Blue

brother in-law wanted Washington Blue, but then decided it was to dark so they started tweaking the color and, this is what he came up with
I think it turned out good
Forum: Model A (1928-31) 06-07-2021, 08:01 PM
Replies: 26
Views: 1,621
Posted By tinkirk
Re: Andalusite Blue

Here's my brother-in-law carhttps://uploads.tapatalk-cdn.com/20210608/557f8cb7c52f2f91a3dbbbd304cc758b.jpg


Sent from my iPhone using Tapatalk
Forum: Model A (1928-31) 06-07-2021, 07:56 PM
Replies: 26
Views: 1,621
Posted By tinkirk
Re: Andalusite Blue

You have picture of your friends car????


Sent from my iPhone using Tapatalk
Forum: Model A (1928-31) 06-02-2021, 05:52 PM
Replies: 11
Views: 405
Posted By tinkirk
Re: Trunk floor in '29 roadster...

https://uploads.tapatalk-cdn.com/20210602/c5db43a12f4c1c5f670b3c0d39619b39.jpg


Sent from my iPhone using Tapatalk
Forum: Model A (1928-31) 06-02-2021, 09:52 AM
Replies: 18
Views: 765
Posted By tinkirk
Re: Rear main bearing cap oil return line question

might want to check crank end play if it is excessive it will act like pump and it will leak
Forum: Model A (1928-31) 05-24-2021, 09:01 PM
Replies: 8
Views: 584
Posted By tinkirk
Re: Does the weber down draft not fit under a stock 28-29 hood?

With the rectangular air cleaner mine would hit the side of my hood, i found a round one that fits the webber carb, problem solved
Can't remember where I found it
Maybe speedway motors


Sent...
Forum: Model A (1928-31) 04-27-2021, 07:49 PM
Replies: 13
Views: 819
Posted By tinkirk
Re: Torque spec for spark plugs?

Tight is tight too tight is broke??


Sent from my iPhone using Tapatalk
Forum: Model A (1928-31) 04-27-2021, 07:47 PM
Replies: 11
Views: 644
Posted By tinkirk
Re: Gilmore "Model A Day" - Sept 18. 2021

You won't be sorry it will make a good time memory for you, lots of nice cars that are driven there from a lot of different states
As long as the event will be held
Have fun,happy motoring

...
Forum: Model A (1928-31) 03-29-2021, 01:19 PM
Replies: 11
Views: 727
Posted By tinkirk
Forum: Model A (1928-31) 03-17-2021, 06:44 PM
Replies: 39
Views: 3,205
Posted By tinkirk
Re: Cross country in a Model A preview

how long are you planning that this trip will take you???
Forum: Model A (1928-31) 03-16-2021, 09:41 AM
Replies: 16
Views: 1,438
Posted By tinkirk
Re: Oil Pump Question

I run a Mike's affordable side cover with a filter and, run10w30 mobile one
on start up cold it will run up to 20+ lbs until warmed up then its back down to where it should 4000 miles no issue's ...
Forum: Model A (1928-31) 03-15-2021, 02:55 PM
Replies: 10
Views: 852
Posted By tinkirk
Forum: Model A (1928-31) 03-15-2021, 02:51 PM
Replies: 13
Views: 804
Posted By tinkirk
Re: Head Stud Q...

ARP will probably have what you might be looking for
Forum: Early V8 (1932-53) 03-14-2021, 03:12 PM
Replies: 9
Views: 529
Posted By tinkirk
Re: Source .100 over Piston rings 255 engine

If you want 4 rings you will need to buy 2 sets
Or just run with three rings is what i was told by Rich at AER in Skokie Il.
The two bottom ones are the same


Sent from my iPhone using Tapatalk
Forum: Early V8 (1932-53) 02-22-2021, 01:56 PM
Replies: 24
Views: 1,593
Posted By tinkirk
Re: 1939 right rear drum install

make sure your parking brake is released
Forum: Model A (1928-31) 02-13-2021, 07:00 PM
Replies: 4
Views: 509
Posted By tinkirk
Re: Drag link hits the tie rod

Put a shorter pitman arm on it maybe


Sent from my iPhone using Tapatalk
Forum: Model A (1928-31) 02-07-2021, 07:35 PM
Replies: 12
Views: 745
Posted By tinkirk
Re: Horn wiring question

Not that I know of
Anyway mine don't


Sent from my iPhone using Tapatalk
Forum: Model A (1928-31) 02-04-2021, 08:48 PM
Replies: 33
Views: 2,452
Posted By tinkirk
Re: Lightened Flywheel?

Stock flywheel is 63
I've got mine down to 37
What's a perfect weight? I guess that would depend on engine and what would work best for your application


Sent from my iPhone using Tapatalk
Forum: Model A (1928-31) 01-24-2021, 06:00 PM
Replies: 10
Views: 757
Posted By tinkirk
Re: how to remove front hub inner bearing seal?

Probably really don't need to replace it
Just clean it all up and, you should be good seeing that its just something to keep the dust and dirt out of the bearing.


Sent from my iPhone using...
Forum: Early V8 (1932-53) 01-20-2021, 05:37 PM
Replies: 14
Views: 1,392
Posted By tinkirk
Re: The Right Stuff

We used it for header gaskets on roundy round car works great
It's the best stuff I've ever used a little bit pricey but will worth it


Sent from my iPhone using Tapatalk
Forum: Model A (1928-31) 01-02-2021, 06:01 PM
Replies: 14
Views: 1,331
Posted By tinkirk
Re: Remove this bolt?

Heat it cherry red and spray with
penetrating oil let it cool down and then try and turn it out
Will almost come out with very little trouble


Sent from my iPhone using Tapatalk
Showing results 1 to 25 of 303

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:48 PM.