Forum: Model A (1928-31)
08-26-2018, 01:47 PM
|
Replies: 5
Views: 1,416
Old radiator with new leakless water pump
Now that I have your attention...
I picked up and installed one of Mr. Rupert's Extreme Duty leakless water pumps. Its a really nice product. The recommendation is to add water pump lubricant to...
|
Forum: Model A (1928-31)
07-13-2017, 04:46 PM
|
Replies: 7
Views: 1,444
|
Forum: Model A (1928-31)
07-13-2017, 10:39 AM
|
Replies: 7
Views: 1,444
Torque tube nuts and bolts
Can't remember how they came off or if it even matters, but should it be bolt, washer, clamshell, nut or bolt,clamshell, washer, nut? Thanks.
|
Forum: Model-A
05-24-2017, 09:00 AM
|
Replies: 3
Views: 1,716
|
Forum: Model-A
05-12-2017, 07:12 PM
|
Replies: 3
Views: 1,716
Re: Dennis Cling Model A hydraulic conversion kit
Still searching...
I've called AZ, NZ, CA chasing leads, but no luck yet.
Does anyone know of someone who has one, but isn't using or maybe planned to use one but has it sitting on a shelf? All...
|
Forum: Model-A
05-02-2017, 02:39 PM
|
Replies: 3
Views: 1,716
|
Forum: Model-A
05-01-2017, 11:47 AM
|
Replies: 3
Views: 1,716
|
Forum: Early V8 (1932-53)
09-05-2016, 05:36 PM
|
Replies: 41
Views: 8,717
|
Forum: Model A (1928-31)
05-06-2016, 04:38 PM
|
Replies: 14
Views: 3,247
Re: Rear hub won't turn
If you're using juice drum and backing plates on your A axles you need to clearance them both. Dennis Cling has a wonderful how-to packet that explains it all.
|
Forum: Early V8 (1932-53)
05-04-2016, 09:53 PM
|
Replies: 3
Views: 1,236
seat adjuster…but from what?
Gents-
This came off the bottom of an alleged '32 sedan bucket seat. I've enclosed pics, but I haven't seen this in any catalogs. Im using the seats in a '30 Coupe, but want to stay true to the...
|
Forum: Model A (1928-31)
11-06-2013, 12:17 PM
|
Replies: 12
Views: 3,084
Re: Axle key to keyway fit
I'll measure up those keys. If the new keys are as good as it gets and I use Tom's advice, could I use a drop of Loctite to keep the key from riding up the keyway?
|
Forum: Model A (1928-31)
11-04-2013, 03:41 PM
|
Replies: 12
Views: 3,084
Axle key to keyway fit
Gents-
Thanks for all your help over the last several months. My rearend is rebuilt using Mr. Endy's disertation, my flywheel trued and installed, engine, clutch and transmission installed and I...
|
Forum: Early V8
11-04-2013, 03:06 PM
|
Replies: 6
Views: 1,863
|
Forum: Model A (1928-31)
09-24-2013, 06:10 PM
|
Replies: 21
Views: 11,897
Re: Rear Axle brake drum hub Shim sleeve ?
I found this thread while boning up on some info, but can I pose a question relating to the shim/hub/axle relationship?
I just rebuilt my entire rear end with the help of Mr. Tom Endy's...
|
Forum: Model A (1928-31)
09-08-2013, 11:23 PM
|
Replies: 4
Views: 1,821
Re: Rear end pre load confusion
Yes, Brent. This helps.
To find the bearing pre-load I ended up with .045" of gasket thickness. Until the above quote from Tom Endy I hadn't seen the .020-.050 figure anywhere and being a complete...
|
Forum: Model A (1928-31)
09-08-2013, 09:22 PM
|
Replies: 4
Views: 1,821
Rear end pre load confusion
Quoted from Mr. Tom Endy elsewhere on the Barn…
The two axle housings should be bolted to the banjo with the carrier inside with out any banjo gaskets. The ring gear should lock up when the bolts...
|
Forum: Model A (1928-31)
04-23-2013, 03:04 PM
|
Replies: 10
Views: 2,287
|
Forum: Model A (1928-31)
03-20-2013, 03:09 PM
|
Replies: 21
Views: 3,759
|
Forum: Model A (1928-31)
02-26-2013, 09:47 PM
|
Replies: 7
Views: 1,883
Re: Torque tube gasket
I can't remember exactly where I read it in the last few days, but I recall reading that the A didn't initially have a gasket at the torque tube. However, gaskets were supplied at some point during...
|
Forum: Model A (1928-31)
02-19-2013, 09:20 PM
|
Replies: 39
Views: 21,935
|
Forum: Model A (1928-31)
02-19-2013, 08:43 PM
|
Replies: 39
Views: 21,935
|
Forum: Model-A
09-30-2012, 09:30 PM
|
Replies: 1
Views: 790
|
Forum: Early V8
09-29-2012, 11:05 AM
|
Replies: 6
Views: 1,863
|
Forum: Early V8
09-23-2012, 06:36 PM
|
Replies: 6
Views: 1,863
|
Forum: Early V8
09-17-2012, 09:59 AM
|
Replies: 6
Views: 1,863
|