Forum: Early V8 (1932-53)
11-28-2017, 09:15 AM
|
Replies: 11
Views: 1,983
|
Forum: Early V8 (1932-53)
10-11-2017, 08:49 AM
|
Replies: 4
Views: 793
1932 Tudor floor question
Hi there - can anyone send me a picture of the underside of the stock floor for a '32 2-door sedan? Specifically the part that is under the front seats? A top-side pic without the seats in could help...
|
Forum: Early V8 (1932-53)
09-27-2017, 02:40 PM
|
Replies: 5
Views: 1,012
|
Forum: Early V8 (1932-53)
09-27-2017, 02:32 PM
|
Replies: 5
Views: 1,012
|
Forum: Early V8 (1932-53)
09-27-2017, 01:42 PM
|
Replies: 5
Views: 1,012
Identifying a Part
Need help in identifying this part. Wide belt 4 3/8 in diameter. Shaft 1 1/16.
Stamped Browning 28K45
|
Forum: Early V8 (1932-53)
09-14-2017, 05:00 PM
|
Replies: 8
Views: 2,194
|
Forum: Early V8 (1932-53)
09-14-2017, 11:36 AM
|
Replies: 8
Views: 2,194
|
Forum: Early V8 (1932-53)
09-13-2017, 11:50 AM
|
Replies: 1
Views: 957
Part Identification-4
Hi Guys! Due to a recent acquisition, I could use some help in identifying the following part: B5A7029035 is the part number given and the item is 33in long. Thanks!
|
Forum: Early V8 (1932-53)
09-13-2017, 11:14 AM
|
Replies: 2
Views: 1,537
Part Identification-3
Hi Guys! Due to a recent acquisition, I could use some help in identifying the following part: BA7325555A is the part number given and the item is 38in long. Thanks!
|
Forum: Early V8 (1932-53)
09-13-2017, 11:09 AM
|
Replies: 1
Views: 984
Part Identification-2
Hi Guys! Due to a recent acquisition, I could use some help in identifying the following part: BM7310739B is the part number given and the item is 39.5in long. Thanks!
|
Forum: Early V8 (1932-53)
09-13-2017, 10:49 AM
|
Replies: 4
Views: 1,314
Part Identification
Hi Guys! Due to a recent acquisition, I could use some help in identifying the following part: BA16003B is the part number given and the item is 33in long. Thanks!
|
Forum: Early V8 (1932-53)
09-08-2017, 12:59 PM
|
Replies: 11
Views: 1,983
Re: 1935 big truck bench seat question
Thanks Don - so you have a full bench on that tank? The folks at Early Ford V8 Sales thought I should have a split bench. The bench I have (not oem btw and missing the wood part) is definitely too...
|
Forum: Early V8 (1932-53)
09-08-2017, 11:56 AM
|
Replies: 11
Views: 1,983
Re: 1935 big truck bench seat question
Then again when I look under the truck it is clear the tank is designed to be there so maybe I have the wrong bench? This is confusing when you're asked to complete what someone else started.
|
Forum: Early V8 (1932-53)
09-08-2017, 11:52 AM
|
Replies: 11
Views: 1,983
|
Forum: Early V8 (1932-53)
09-08-2017, 11:40 AM
|
Replies: 11
Views: 1,983
Re: 1935 big truck bench seat question
Hi - thanks for the reply. I get that part ok. The problem I am experiencing is that I am having interference with the gas tank fill neck. The "metal platform" is the gas tank itself with 2...
|
Forum: Early V8 (1932-53)
09-08-2017, 10:47 AM
|
Replies: 11
Views: 1,983
1935 big truck bench seat question
Hello friends and thanks for looking at my thread: a customer brought me a project and one of them involves the installation of a bench seat over the gas tank. The wooden part of the bench is MIA but...
|
Forum: Early V8 (1932-53)
05-20-2017, 10:26 AM
|
Replies: 10
Views: 1,558
GM alt in a flathead question
Pictured is the back of the 12v GM alternator I have to install in a customer's 24 stud motor. What is the smaller post directly below the positive one? If it's a 1wire it should be ground but is...
|
Forum: Early V8 (1932-53)
05-03-2017, 09:31 AM
|
Replies: 5
Views: 1,248
Re: Rear Wide Five madness! What have I got?
Thanks! That is correct. My predecessor used the smaller bearings despite the fact that they are about 1/4" too short for the depth of the hub, then used the full-sized seal leaving the bearing able...
|
Forum: Early V8 (1932-53)
05-02-2017, 09:20 AM
|
Replies: 6
Views: 716
|
Forum: Early V8 (1932-53)
05-02-2017, 09:03 AM
|
Replies: 5
Views: 1,248
Rear Wide Five madness! What have I got?
So my customer's rear wide-fives were shot so I located another pair to replace them. Set 1 came off the truck with normal wheel bearing arrangement: 3" diameter, full depth. When I opened the grease...
|
Forum: Early V8 (1932-53)
05-01-2017, 04:24 PM
|
Replies: 6
Views: 716
Re: 1937 pickup front motor mounts
Thanks for the responses. You've both confirmed what I suspected and a course of action. So I did that and now have this problem. What the hell is going on here?!! I cannot for the life of me get the...
|
Forum: Early V8 (1932-53)
05-01-2017, 08:24 AM
|
Replies: 6
Views: 716
1937 pickup front motor mounts
Hi - having a little trouble figuring out a front motor mount issue - it looks like I have some rivits in the way of having a flat mounting surface. I am using a mount kit available through the...
|
Forum: Early V8 (1932-53)
04-18-2017, 08:21 AM
|
Replies: 2
Views: 1,038
|
Forum: Early V8 (1932-53)
04-17-2017, 07:22 AM
|
Replies: 2
Views: 1,038
1939 brake/clutch pedal and master cyl assembly
Hi- can someone please do me the HUGE favor of posting to this thread a pic of the assembly of where the pedal set and master cyl meets the frame of a '39? I'm kind of a visual guy and can't find an...
|
Forum: Early V8 (1932-53)
12-11-2016, 01:06 PM
|
Replies: 22
Views: 3,573
|