Forum: Early V8 (1932-53)
12-13-2023, 12:12 PM
|
Replies: 0
Views: 272
Slingshot on 8ba Fuel Pump Pushrod Length
Hello All:
I have done alot of searching, thought somebody might have a definitive hard number that would save a bunch of measuring:
What should the Fuel Pump pushrod length be for an Edelbrock...
|
Forum: Early V8 (1932-53)
08-03-2023, 11:45 AM
|
Replies: 11
Views: 719
|
Forum: Early V8 (1932-53)
08-03-2023, 10:47 AM
|
Replies: 11
Views: 719
|
Forum: Early V8 (1932-53)
07-20-2023, 08:59 PM
|
Replies: 6
Views: 507
|
Forum: Early V8 (1932-53)
07-20-2023, 04:52 PM
|
Replies: 6
Views: 507
|
Forum: Early V8 (1932-53)
07-20-2023, 04:16 PM
|
Replies: 6
Views: 507
Odyssey Battery w Generator
Hello All:
Posted this over on the HAMB too (got some good insight, just wanting to see if anyone here has ever actually run one)- has anybody used the Odyssey PC680 w a generator (12V)??
If...
|
Forum: Early V8
07-06-2023, 02:41 PM
|
Replies: 0
Views: 317
Edmunds Intake W 2 Stromberg 81s
Very nice Edmunds intake w 2 very nice Stromberg 81's. Pulled this off of my running car a few years back, I would go through the carbs. They are move freely and are very clean. Includes linkage and...
|
Forum: Early V8
06-30-2023, 01:11 PM
|
Replies: 0
Views: 343
|
Forum: Early V8 (1932-53)
06-01-2023, 08:35 PM
|
Replies: 1
Views: 425
1934 radius rods to torque tube bolt question
Hello All- in looking under my 34 project, it looks like the bolt and nut attaching the radius rods to the torque tube are incorrect (no cotter pin). I have the correct bolt, nut, and cotter pin- my...
|
Forum: Early V8 (1932-53)
02-11-2023, 04:17 PM
|
Replies: 3
Views: 488
|
Forum: Early V8 (1932-53)
02-11-2023, 03:19 PM
|
Replies: 3
Views: 488
Help- mismatched cam and timing cover
Whelp, I thought I had everything perfectly509480 planned, my Flathead newbie status was just exposed. It appears as though the I have a long snout cam and my 2 bolt timing cover won’t allow the...
|
Forum: Early V8 (1932-53)
02-09-2023, 07:32 PM
|
Replies: 20
Views: 2,309
Re: Crab distributor question
I have a few to choose from, good eye- the edelbrock regular dual does well at placing the carbs over the intake ports, but I may run my Navarro reg dual. I haven’t decided yet.
|
Forum: Early V8 (1932-53)
02-08-2023, 02:35 PM
|
Replies: 20
Views: 2,309
|
Forum: Early V8 (1932-53)
02-06-2023, 10:23 PM
|
Replies: 20
Views: 2,309
Re: Crab distributor question
Thanks very much guys- I’ve read a lot about vacuum brake no vacuum brake- I know Bubbas had indicated it should be used. Makes sense that the higher octane/ low compression reality renders the...
|
Forum: Early V8 (1932-53)
02-06-2023, 12:39 PM
|
Replies: 20
Views: 2,309
Re: Crab distributor question
Drake pumps, sealed bearings- no need to seal extra hole up top in block (water pump).
Correct 59a Cam gears for proper thrust
Holes in block sealed with welch plugs
Not sealing the pan-...
|
Forum: Early V8 (1932-53)
02-06-2023, 12:31 PM
|
Replies: 20
Views: 2,309
|
Forum: Early V8 (1932-53)
02-05-2023, 08:56 PM
|
Replies: 20
Views: 2,309
Re: Crab distributor question
Thanks- yes, the manifold is an edelbrock regular dual, it does have a port under the back carb, I’m sure I will have to make some stuff to get it all sorted. Really just wanted to make sure I get...
|
Forum: Early V8 (1932-53)
02-05-2023, 08:22 PM
|
Replies: 20
Views: 2,309
Re: Crab distributor question
Great, thanks-I will give them a shout tomorrow- yes, I understand vacuum signal comes from manifold, not the other way around😀
|
Forum: Early V8 (1932-53)
02-05-2023, 07:34 PM
|
Replies: 20
Views: 2,309
Crab distributor question
Hello All:
I just want to make sure I have my ducks in a row- I have dressed the front of my 8ba with early pumps, cam, 2 bolt timing cover, pulley, etc. I am going to run a stock rebuilt crab...
|
Forum: Early V8
01-29-2023, 03:05 PM
|
Replies: 1
Views: 583
|
Forum: Early V8 (1932-53)
01-19-2023, 05:14 PM
|
Replies: 5
Views: 704
|
Forum: Early V8
01-19-2023, 01:25 PM
|
Replies: 1
Views: 583
|
Forum: Early V8 (1932-53)
01-19-2023, 01:20 PM
|
Replies: 5
Views: 704
8ba road draft Inner tube removal
Hi guys:
What is the best way to remove the inner part of the road draft tube (in the valley)??. I tried grabbing it with vice grips, it doesn't seem to want to move.
Thanks in Advance,
Dave
|
Forum: Early V8
01-14-2023, 07:16 PM
|
Replies: 1
Views: 442
|
Forum: Early V8
01-14-2023, 03:01 PM
|
Replies: 1
Views: 442
|