Forum: Model A (1928-31)
12-16-2021, 09:07 AM
|
Replies: 22
Views: 5,111
Re: Engine Rebuild Guide
Now we know why it makes sense to take a hard look at the Burtz Engine as a comparison that has been reengineered to eliminate the failures of the "A" engine and at a reasonable cost when you compare...
|
Forum: Model A (1928-31)
10-31-2021, 11:52 AM
|
Replies: 13
Views: 1,469
Re: Electrical Problems
I would bet on the ground to battery connections or starter switch on top of starter Goood luck. Sofield
|
Forum: Model A (1928-31)
09-17-2021, 04:10 PM
|
Replies: 16
Views: 3,524
Re: V8 Clutch for model A
Hello Jim, Do you remember or know the part number of the diaphragm clutch or the year of the Ford Ranger pickup? What is the bolt mounting pattern like or is it the same as the early V8?
You answer...
|
Forum: Model A (1928-31)
08-23-2021, 09:03 AM
|
Replies: 9
Views: 2,457
Re: Installing new Distributor Bushings ????
Very simple: You need the following: A 5/16” bolt or threaded rod that is long enough to pass through two bushings and the distributor bore, two washers and nuts. Put a washer and bushing on one end...
|
Forum: Model A (1928-31)
08-23-2021, 08:35 AM
|
Replies: 9
Views: 2,457
Re: Installing new Distributor Bushings ????
Very simple solution: You need a 5/16 bolt or threaded rod that is long enough to pass through the distributor plus the length of two bushings. put a washer or a washer and nut at both ends of the of...
|
Forum: Model A (1928-31)
07-11-2021, 09:48 AM
|
Replies: 17
Views: 2,459
Re: Front spindles
Just put an ad in the wanted section of the Barn and you will be surprised at the response.
|
Forum: Model A (1928-31)
06-30-2021, 08:40 AM
|
Replies: 7
Views: 1,307
Re: Engine mounts
Good question, As designed the stock mounts with the rubber pads and bolted to the engine was an integral part of the structure of the frame and acted as a cross member. The float a motor mounts may...
|
Forum: Model A (1928-31)
06-30-2021, 07:51 AM
|
Replies: 30
Views: 3,603
Re: Front spring broken
I have seen this before. The reason that this was done was the cross member was cracked and instead of replacing the cross member this was the easiest way to correct the problem. You should be able...
|
Forum: Model A (1928-31)
06-19-2021, 10:22 PM
|
Replies: 9
Views: 1,340
|
Forum: Model A (1928-31)
06-19-2021, 05:55 PM
|
Replies: 14
Views: 1,591
|
Forum: Model A (1928-31)
06-19-2021, 07:06 AM
|
Replies: 14
Views: 1,591
Re: Front Cross Member Question
Contact Bolt Depot in MA. You can get the six necessary 1/4" recessed bolts that will be flush with the top of frame including the other 8 bolts for the sides and bottoms of the frame in #8.
|
Forum: Model A (1928-31)
06-06-2021, 07:41 AM
|
Replies: 6
Views: 1,414
Re: Brakes Discoveries
Does the car sag on the drivers side? This would be a good reason for the problem. I believe the quote in #3 has hit the nail on the head.
Sofield
|
Forum: Model A (1928-31)
01-12-2021, 01:30 PM
|
Replies: 10
Views: 1,233
|
Forum: Model A (1928-31)
01-11-2021, 08:50 AM
|
Replies: 19
Views: 2,548
|
Forum: Model A (1928-31)
01-01-2021, 03:16 PM
|
Replies: 2
Views: 829
Clutch finger adjustment
When trying to adjust the fingers on the clutch plate, is the plate bolted to the flywheel and disc and the adjustment being between 5/8 & 11/16 after final adjustment Your answers are appreciated.
|
Forum: Model A (1928-31)
01-01-2021, 02:47 PM
|
Replies: 15
Views: 1,916
Re: Engine heat in cold weather
How did you arive that there was a difference in the engine temperature with the heater on or off? Are you running a temperature gangue?
|
Forum: Model-A
12-30-2020, 08:59 PM
|
Replies: 0
Views: 523
|
Forum: Model A (1928-31)
12-06-2020, 08:52 AM
|
Replies: 26
Views: 4,277
Re: Bad Stud thread
Bratton's supplies a tool jig kit #8235 that allows you to drill out the stud without disturbing or removing any of the other studs. The jig comes with a locating guide and bushings, a burr to center...
|
Forum: Model A (1928-31)
11-22-2020, 05:55 PM
|
Replies: 12
Views: 2,176
|
Forum: Model A (1928-31)
11-19-2020, 12:25 PM
|
Replies: 3
Views: 1,115
Re: Clutch finger depth
Is the 11/16 measurement with the plate and disc bolted to flywheel?
Thanks for a response.
|
Forum: Model-A
10-30-2020, 03:45 PM
|
Replies: 0
Views: 766
Used Model "A" Engine
I bought a used running engine sight unseen for a project car. The car owner changed his mind and decided on a rebuilt engine. After I received the engine prior to the customer changing his mind I...
|
Forum: Model-A
10-28-2020, 06:23 PM
|
Replies: 0
Views: 628
Pair of 30 and 31 Rear Fenders
For Pickup/Roadster/Coupe. Original very good condition. no dents / excellent beads / no rips. Sand/prime/paint and put on your car. Shipping additional or pick up.
|
Forum: Model-A
10-17-2020, 03:38 PM
|
Replies: 0
Views: 655
|
Forum: Model A (1928-31)
10-02-2020, 07:05 PM
|
Replies: 3
Views: 1,107
|
Forum: Model A (1928-31)
09-26-2020, 10:48 AM
|
Replies: 36
Views: 8,890
Re: Exhaust Manifold to Tailpipe gasket
Nobody has mentioned to loosen the tail pipe bracket at the rear to help with the alignment. This allows for a forward and rotational movement of the pipe.
|