Forum: Early V8 (1932-53)
01-12-2024, 09:56 PM
|
Replies: 10
Views: 629
|
Forum: Early V8 (1932-53)
12-06-2023, 10:14 AM
|
Replies: 33
Views: 4,155
Re: 1937 model 74 blowing the blues
I have some oddball (since I don’t have any 60’s) valves, if I knew the overall length maybe that’s what they are. Longer than my 21 stud mushrooms. Can have them if fit
|
Forum: Late V8
12-03-2023, 08:18 PM
|
Replies: 0
Views: 469
Bellhousing & such, 289
Have a motor 289, & 3 speed transmission, need all the stuff to go between. Fork, fulcrum, spring, plate& bell, flywheel clutch. Somewhere in fl, south Alabama, south ga.
|
Forum: Early V8 (1932-53)
10-21-2023, 08:17 AM
|
Replies: 10
Views: 645
Re: 48 Ford how much play on rear driveshaft yoke
Drag should be something like 1.7 in # I thought, rather than toggle something up I elected to do it by “ feels good” that is enclosed, but same thing. If it feels gritty, I would pull it out &...
|
Forum: Early V8 (1932-53)
10-21-2023, 08:03 AM
|
Replies: 23
Views: 1,617
|
Forum: Model A (1928-31)
07-17-2023, 11:44 AM
|
Replies: 24
Views: 2,183
Re: How much oil from L to notch on dipstick?
My White Construcktor 855 motor held 5 gallons, add mark was 2 quarts low. Starting out every morning I topped it off, most of 2 quarts Rotella. After a couple weeks, I let it go, and it stayed at...
|
Forum: Early V8 (1932-53)
03-12-2023, 10:55 AM
|
Replies: 9
Views: 1,257
|
Forum: Early V8 (1932-53)
02-11-2023, 05:40 PM
|
Replies: 15
Views: 1,898
|
Forum: Early V8 (1932-53)
02-11-2023, 09:54 AM
|
Replies: 15
Views: 1,898
Re: Help with engine Id
Not to be smart, but lots of previous discussion on it. Challenging enough, without looking for another block. I went overboard and did a stand with exhaust mounts on both sides....
|
Forum: Early V8 (1932-53)
02-10-2023, 10:30 AM
|
Replies: 15
Views: 1,898
|
Forum: Model A (1928-31)
02-07-2023, 11:21 AM
|
Replies: 13
Views: 2,289
Re: frame repair
I have a right side rail for repair of a frame that was stored in the mud on that side. A challenge to rivet back in but… I recall it was pretty good. Since the left side has the vehicle has your ID...
|
Forum: Early V8 (1932-53)
01-26-2023, 07:49 PM
|
Replies: 8
Views: 990
|
Forum: Early V8 (1932-53)
01-16-2023, 08:38 AM
|
Replies: 25
Views: 4,028
Re: wide 5s
I have one like that, someone put a split rim outer rim on a center from a wide 5. Very heavy, and a crappy weld job. There should be a rim with the same ID as wide 5, junkyard shopping with a ruler....
|
Forum: Early V8 (1932-53)
01-16-2023, 08:21 AM
|
Replies: 20
Views: 3,549
|
Forum: Early V8 (1932-53)
01-14-2023, 11:01 AM
|
Replies: 76
Views: 9,197
Re: '36 221 - rebuildable??
I have been collecting bearing sets as they come up cheap for about 30 years, I can see what I have for full floating. I have 2 early motors that are not fresh so after I have saved some for that no...
|
Forum: Model A (1928-31)
01-10-2023, 10:34 AM
|
Replies: 20
Views: 4,938
Re: Re-Stamping Engine Number / Frame Number
I lived there for way too long. DMV does not want to let you get what you need, their goal is to deny. No ‘spect for any NY bureaucracy. Pennsylvania was much better, Florida I get everything done...
|
Forum: Early V8 (1932-53)
12-12-2022, 11:44 AM
|
Replies: 5
Views: 839
|
Forum: Early V8 (1932-53)
12-08-2022, 09:42 AM
|
Replies: 76
Views: 9,197
|
Forum: Model A (1928-31)
08-24-2022, 05:34 PM
|
Replies: 7
Views: 1,242
|
Forum: Early V8 (1932-53)
08-18-2022, 06:39 AM
|
Replies: 31
Views: 2,157
|
Forum: Early V8 (1932-53)
08-17-2022, 06:32 PM
|
Replies: 31
Views: 2,157
Re: Remove 1 ton rear brake removal
When you get the tab bent up and can get the nut off & the lock plate off, could go tighten the inner nut to observe the amount of adjustment, probably less than 1/4 turn. Then if cone and cups look...
|
Forum: Model-A
08-04-2022, 06:37 AM
|
Replies: 0
Views: 460
Motor
Motor turns with starter, has governor for power unit. Also rear axle, tube, bones. Yes have pictures
|
Forum: Model-T
08-04-2022, 06:33 AM
|
Replies: 0
Views: 549
Mechanical parts
Have to move and can’t take it all,motors, transmissions, suspension and axles, lights, starters, etc.. Don’t want any going to scrap. Pm for pictures & contact
|
Forum: Early V8 (1932-53)
07-27-2022, 04:28 PM
|
Replies: 2
Views: 672
|
Forum: Model T (1909-1927)
07-26-2022, 07:36 PM
|
Replies: 2
Views: 1,218
Re: America First
Yup, a local industry where I used to live, back when the area was booming. Older buddy said could get 2 jobs, late for one or duck out early and not get fired. Make a bunch of 1960 munny
|