Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 129
Search took 0.01 seconds.
Search: Posts Made By: Randy/In
Forum: Early V8 (1932-53) 07-08-2016, 07:38 PM
Replies: 26
Views: 3,195
Posted By Randy/In
Re: 21 stud timing cover differences?

You can drill one of the timing cover mounting bolts and fabricate a pointer pin to fit it.
Forum: Early V8 (1932-53) 02-14-2016, 07:26 PM
Replies: 7
Views: 1,774
Posted By Randy/In
Re: Harman Collins points part numbers???

Ok, I found the Bendix number, 10-357174.
Forum: Early V8 (1932-53) 02-14-2016, 07:17 PM
Replies: 7
Views: 1,774
Posted By Randy/In
Re: Harman Collins points part numbers???

They are used in Bendix 20 or 200 series magnetos. I can get the number tomorrow if you still need it.
Forum: Early V8 (1932-53) 09-18-2015, 01:45 PM
Replies: 8
Views: 2,081
Posted By Randy/In
Re: Looking for Flathead friendly Machine shop near Chicago

I you want to come south a little, there is Van Senus in Hammond Indiana.
Forum: Early V8 (1932-53) 09-04-2015, 07:49 PM
Replies: 6
Views: 1,074
Posted By Randy/In
Re: Motor ID

Why is the engine junk?
Forum: Early V8 (1932-53) 09-01-2015, 05:14 AM
Replies: 3
Views: 995
Posted By Randy/In
Re: magneto points for anlz cnversion to ford

Do you have a picture of the old ones?. Look for a part no. On the points base.
Forum: Early V8 (1932-53) 08-30-2015, 04:17 PM
Replies: 2
Views: 599
Posted By Randy/In
Re: Removing Clutch and Brake pedal 1936

I had to drill mine out, then press the shaft out.
Forum: Early V8 (1932-53) 07-02-2015, 07:04 PM
Replies: 11
Views: 1,674
Posted By Randy/In
Re: 35/36 Ford Fuel Pump Gasket Material

Roy Nacewicz shows the gasket in his online catalog. www.fordbolts.com (http://www.fordbolts.com).
Forum: Early V8 (1932-53) 04-04-2015, 06:53 PM
Replies: 4
Views: 853
Posted By Randy/In
Re: Measurement please..35/37 pickup cab

My 35 is also 12 inches.
Forum: Early V8 (1932-53) 03-08-2015, 03:49 PM
Replies: 24
Views: 4,505
Posted By Randy/In
Re: Need some motor installation help

I had a similar problem with a 35 sedan, I loosened the rear spring u bolts, installed trans mount bolts, then retighten rear spring u bolts.
Forum: Early V8 (1932-53) 02-01-2015, 08:08 PM
Replies: 22
Views: 5,579
Posted By Randy/In
Re: Trailer tie-down discussion

I tow a 20 foot enclosed trailer and 35 pick up with a F150 rated at pulling a 9400 lb. Trailer, no problems yet. I also pull horse trailers and a 8200 lb. Travel trailer. I use the wheel style...
Forum: Early V8 (1932-53) 01-23-2015, 12:53 PM
Replies: 3
Views: 884
Posted By Randy/In
Re: Oil Pumps ?

Here is a picture of a early pump from my 35
Forum: Early V8 (1932-53) 08-29-2014, 12:03 PM
Replies: 9
Views: 1,705
Posted By Randy/In
Re: Oil Pan Dipstick Tube Boss

Heli-coil it. I did one that way.
Forum: Early V8 (1932-53) 08-24-2014, 10:06 AM
Replies: 35
Views: 5,565
Posted By Randy/In
Re: On-Off Battery Cable 6volt

You can look at the ones Mcmaster Carr shows in their online catalog. that is where I got mine.
Forum: Early V8 (1932-53) 07-30-2014, 06:14 PM
Replies: 18
Views: 2,523
Posted By Randy/In
Forum: Early V8 (1932-53) 05-01-2014, 05:24 PM
Replies: 7
Views: 1,820
Posted By Randy/In
Re: Press on aluminium cam gear

I bought my last one from Little Dearborn parts.
Forum: Early V8 (1932-53) 03-29-2014, 12:11 PM
Replies: 1
Views: 851
Posted By Randy/In
Early oil pump

Is there problems using these early style oil pumps if they are in good condition?
Forum: Early V8 (1932-53) 03-24-2014, 05:37 PM
Replies: 8
Views: 1,474
Posted By Randy/In
Re: Oil pump gasket

Thanks for the replies, this pump will be going together without a gasket. the gasket would add .008" to the pump clearance to cover.
Forum: Early V8 (1932-53) 03-21-2014, 04:30 PM
Replies: 8
Views: 1,474
Posted By Randy/In
Oil pump gasket

Hi, Is there a gasket between the oil pump housing and cover on a 50# long style pump?. Also does any one have a source for the rivet installed in the oil pump drive gear and impeller shaft?. Thanks,...
Forum: Early V8 (1932-53) 05-21-2012, 07:12 PM
Replies: 7
Views: 1,257
Posted By Randy/In
Re: bearing on king pin location

Mine are on top of the axle.
Forum: Early V8 (1932-53) 05-19-2012, 08:43 PM
Replies: 18
Views: 5,646
Posted By Randy/In
Re: Sand Blast Cabinet Gloves ???

Slip a leather glove over the left rubber glove.
Forum: Early V8 (1932-53) 05-04-2012, 06:10 PM
Replies: 2
Views: 737
Posted By Randy/In
Piston ID

I removed these pistons from a 1935 engine that I plan on rebuilding. I have never seen these type with the piston pin retained by a circlip in the connecting rod bushing. I am wandering if this was...
Forum: Early V8 (1932-53) 04-29-2012, 07:54 PM
Replies: 12
Views: 1,652
Posted By Randy/In
Re: new engine - old problem

Where is the vacuum tap for the distributor, From carb, or manifold?
Forum: Early V8 (1932-53) 02-19-2012, 10:22 PM
Replies: 117
Views: 39,825
Posted By Randy/In
Re: 1937 Ford Fordor Survivor

Hi Tony, That is a nice find, I hope you keep it original. Is that the one you have been after for awile? Randy
Forum: Early V8 (1932-53) 01-04-2012, 09:41 PM
Replies: 6
Views: 1,417
Posted By Randy/In
Re: 35 steering box rebuild instructions

Here is the directions I used when rebuilding my steering boxes.
Showing results 1 to 25 of 129

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:20 PM.