Forum: Model A (1928-31)
03-04-2018, 04:03 PM
|
Replies: 4
Views: 1,476
Re: 1930 coupe Body adjusting
I have the radiator and shroud all attached. the hood on and working to adjust the front of the body height so that the hood fits good. the problem I'm having is I have to raise the body up more than...
|
Forum: Model A (1928-31)
02-26-2018, 08:14 AM
|
Replies: 4
Views: 1,476
1930 coupe Body adjusting
I've just set my body on the frame and also have all the other sheet metal bolted together. Now I need to start shimming and adjusting the hood and body to fit properly. Where should I start? Any...
|
Forum: Model A (1928-31)
02-08-2018, 09:32 AM
|
Replies: 8
Views: 1,597
|
Forum: Model A (1928-31)
02-08-2018, 08:58 AM
|
Replies: 8
Views: 1,597
Painted radiator shell
I have a non chromed but Rusty painted radiator shell. It appears to be off a Model A style car. What year did they use painted radiator shells
|
Forum: Model-A
01-02-2016, 05:53 PM
|
Replies: 0
Views: 895
looking for 1930 splash shields
Im in need of two side splash shields with good lower edges. even if the upper part is not good but the lower needs to be good.
|
Forum: Model A (1928-31)
01-02-2016, 05:35 PM
|
Replies: 4
Views: 1,778
1930 splash shield repair
Im wanting to reuse my orignal splash shields but the part that meets the running boards is rusted and deteriorated. Is there any parts available to repair that edge?
|
Forum: Model A (1928-31)
09-07-2015, 09:42 AM
|
Replies: 9
Views: 3,480
|
Forum: Model A (1928-31)
09-07-2015, 08:40 AM
|
Replies: 9
Views: 3,480
|
Forum: Model A (1928-31)
09-07-2015, 08:27 AM
|
Replies: 9
Views: 3,480
|
Forum: Model A (1928-31)
09-07-2015, 07:30 AM
|
Replies: 9
Views: 3,480
Re: splash shield to running board fitting??
I have the front and rear fenders mounted and they fit pretty well. the problem now is that the rear fenders where they meet the rear of the running board are not correct. the fenders are .5 inches...
|
Forum: Model A (1928-31)
09-06-2015, 04:46 PM
|
Replies: 9
Views: 3,480
splash shield to running board fitting??
im putting togather my 1930 deluxe coupe. i have new running boards and im using my orignal splash shields. how do the splash shields attach to the long part of the running board?
|
Forum: Model A (1928-31)
09-06-2015, 09:14 AM
|
Replies: 4
Views: 2,346
|
Forum: Model A (1928-31)
09-06-2015, 08:44 AM
|
Replies: 4
Views: 2,346
|
Forum: Model A (1928-31)
09-06-2015, 07:37 AM
|
Replies: 4
Views: 2,346
1930 model A rear fender brackets
I have new rear fenders and now need to install the rear fender brackets. its been over a year since i removed the brackets so now i dont know where they mount to. Can anyone help me. A bit...
|
Forum: Model A (1928-31)
08-28-2015, 07:00 PM
|
Replies: 2
Views: 1,441
|
Forum: Model A (1928-31)
08-28-2015, 06:46 PM
|
Replies: 2
Views: 1,441
1930 deluxe coupe body blocks
Im installing my body onto the frame. what goes between the blocks and the frame and between the blocks and the body. I have rubber shims and asphalt welting but not sure what goes where.
|
Forum: Model A (1928-31)
09-22-2014, 08:10 PM
|
Replies: 6
Views: 2,695
Re: Clutch pressure plate help
that was very interesting but i dont under stand what is ment by the "cover"
"adjust the nut until you get a distance of 11/16", measured from the top face of the rear of the lever, down onto the...
|
Forum: Model A (1928-31)
09-22-2014, 07:20 PM
|
Replies: 6
Views: 2,695
Clutch pressure plate help
im installing the pressure plate on my 1930 model A engine. freshly turned fly wheel , new clutch disk. After tightening the pressure plate I measured the finger to top of pressure plate. the book...
|
Forum: Model A (1928-31)
03-26-2014, 12:26 PM
|
Replies: 6
Views: 2,492
|
Forum: Model A (1928-31)
03-25-2014, 09:45 PM
|
Replies: 6
Views: 2,492
|
Forum: Questions & Suggestions
01-16-2014, 03:26 PM
|
Replies: 2
Views: 808
|
Forum: Model A (1928-31)
01-16-2014, 03:11 PM
|
Replies: 12
Views: 3,473
Re: Main bearing/babit help
ok im feeling a little better now. i was thinking i was headed for $$$$ with no other options. the center main bearings are much better than the rear bearing.yes i will only be driving limited amouts
|
Forum: Model A (1928-31)
01-16-2014, 12:38 PM
|
Replies: 12
Views: 3,473
Re: Main bearing/babit help
just checking things out i have never had the engine running. i was hoping to dissemble and clean and reassemble but now im not sure what to do.
|
Forum: Model A (1928-31)
01-16-2014, 10:30 AM
|
Replies: 12
Views: 3,473
Main bearing/babit help
ive dissembled my Model A engine. sad to fine it in worse shape than i thought i would fine. here are a few pics of the rear bearing area. whats your opinion on what is my best repair options now?
|
Forum: Model A (1928-31)
01-14-2014, 09:23 PM
|
Replies: 21
Views: 5,415
|