Forum: Model A (1928-31)
03-15-2024, 12:14 PM
|
Replies: 14
Views: 623
Re: Wire wheel balancing
If you added your general location to your profile someone might recommend a shop to do the work for you. You could also contact local clubs for recommendations. I always felt that the things were...
|
Forum: Model A (1928-31)
03-15-2024, 10:08 AM
|
Replies: 9
Views: 291
Re: Narrow bed or wide bed
If you have the fenders you can tell which came with the truck from the factory. If you don't have the fenders for a wide bed they are almost impossible to find. If I needed a truck to use I would...
|
Forum: Model A (1928-31)
03-13-2024, 12:38 AM
|
Replies: 11
Views: 657
Re: Engine paint
It is my understanding that Ford used to dump the left over paint from dipping other parts into the paint for the engine thus there was a wide range of light or darkness to the green. I always had...
|
Forum: Model A (1928-31)
03-11-2024, 12:26 PM
|
Replies: 29
Views: 1,422
Re: Synchronized Transmission
Everyone assumes you have a pickup truck based on the passenger vehicle chassis when talking about the Mitchell. You don't by any chance have a large truck, AA?
Also, put your general location in...
|
Forum: Model A (1928-31)
03-10-2024, 05:54 PM
|
Replies: 6
Views: 519
Re: Need Cylinder Head
Be sure to contact your local club as shipping probably will be more than the price of the head. Good aftermarket high compression heads have destroyed the value of original heads.
Charlie...
|
Forum: Early V8 (1932-53)
03-09-2024, 05:18 PM
|
Replies: 11
Views: 407
|
Forum: Model A (1928-31)
03-09-2024, 05:09 PM
|
Replies: 6
Views: 346
|
Forum: Model A (1928-31)
03-06-2024, 01:26 PM
|
Replies: 11
Views: 615
Re: Luggage weight
Have you considered the racks that bolt onto the running boards?
Charlie Stephens
|
Forum: Model A (1928-31)
03-01-2024, 10:48 AM
|
Replies: 22
Views: 1,158
Re: Wheel stud replacement
...and hole saw and someone who has done it before. Ask at your local club for recommendations. Put your general location in your profile and you may get recommendations.
Charlie Stephens
|
Forum: Model A (1928-31)
02-29-2024, 03:15 PM
|
Replies: 7
Views: 604
Re: A Flywheel on a B
Yes, UNLESS (if I remember correctly) you are running a Model B transmission in which case it will interfere with the bell housing unless you have it cut down slightly.
Charlie Stephens
|
Forum: Early V8 (1932-53)
02-28-2024, 02:13 PM
|
Replies: 46
Views: 2,267
|
Forum: Model A (1928-31)
02-25-2024, 10:49 AM
|
Replies: 4
Views: 394
Re: Ford wire wheel
The correct way to measure a rim is where the tire bead seats. This will be about 1 1/2 inches less than the overall diameter. My guess is that the 18 1/2 if for a 17 inch tire (1933-34) and the 17...
|
Forum: Early V8 (1932-53)
02-20-2024, 06:37 PM
|
Replies: 11
Views: 609
Re: Grant
...and while we are on the topic, what is your general area. You can never tell when this information will be important.
Charlie Stephens
|
Forum: Early V8 (1932-53)
02-20-2024, 06:35 PM
|
Replies: 11
Views: 609
Re: Grant
I also have a 4 door Model B. How about some more info. Restored, original?
Charlie Stephens
|
Forum: Early V8 (1932-53)
02-20-2024, 04:50 PM
|
Replies: 6
Views: 502
Re: BB stamped on my 36 ford
Engines were not serial numbered except for those going to a few locations that required it. Are there any numbers after the BB?
Charlie Stephens
|
Forum: Early V8 (1932-53)
02-20-2024, 04:41 PM
|
Replies: 28
Views: 1,047
Re: Find out more about my '37 fordor
The fact that the VIN is visible through the windshield on modern cars says there is probably no need to hide it. If you are concerned used "XX" for the last numbers. The VIN will give you some...
|
Forum: Early V8 (1932-53)
02-13-2024, 10:47 AM
|
Replies: 9
Views: 565
|
Forum: Questions & Suggestions
02-07-2024, 04:11 PM
|
Replies: 1
Views: 221
|
Forum: Model A (1928-31)
01-17-2024, 11:13 PM
|
Replies: 34
Views: 4,104
Re: Claim of 25% HP bump true?
I was just going to post to watch out for the top end. Be sure there is adequate clearance between the head and the piston. The original and many reproductions had a recess in the head above the...
|
Forum: Early V8 (1932-53)
01-14-2024, 01:40 PM
|
Replies: 24
Views: 930
|
Forum: Early V8 (1932-53)
01-09-2024, 08:58 PM
|
Replies: 25
Views: 1,621
|
Forum: Questions & Suggestions
01-09-2024, 08:48 PM
|
Replies: 1
Views: 507
Re: Relays on 33 Ford pickup
Just a couple of hopefully useful comments:
You posted in an area of Fordbarn that deals with questions & suggestions to the editors about the site. Few people will see your question or respond. ...
|
Forum: Early V8 (1932-53)
01-07-2024, 03:32 PM
|
Replies: 14
Views: 1,040
Re: Simple wiring diagram for dummies
If I was doing it I would buy a reproduction wiring harness. Some suppliers probably have an option to include a right brake light and turn signals which I would recommend if you intend to drive the...
|
Forum: Early V8 (1932-53)
01-07-2024, 03:16 PM
|
Replies: 10
Views: 429
|
Forum: Model A (1928-31)
01-07-2024, 02:57 PM
|
Replies: 3
Views: 411
Re: Model A vacuum wiper question
If I remember correctly the first step is to chemically remove the old chrome but this process dissolves the wiper body. The solution used to be to get a painted wiper off of a standard vehicle and...
|