Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.11 seconds.
Search: Posts Made By: rotorwrench
Forum: Late V8 (1954+) Today, 10:30 AM
Replies: 7
Views: 162
Posted By rotorwrench
Re: 71 LTD Info Wanted

The 1971 models with the 400 were the first of the 335 series 400s and they were the best of the batch. When Ford changed the deck height, it really changed all of the 335 series but the largest...
Forum: Early V8 (1932-53) Today, 10:22 AM
Replies: 13
Views: 553
Posted By rotorwrench
Re: Pre 1945 Block Cams

All of the flathead V8s will crack in the valve pockets if they get too hot. As mentioned, the chances of that do increase with closer distance to cylinder dimensions and especially if they are rode...
Forum: Early V8 (1932-53) Today, 10:07 AM
Replies: 8
Views: 268
Posted By rotorwrench
Re: 32 amp gauge

It depends entirely on what coil a person is using. If it has a helmet type distributor or a later crab/rabbit ear distributor and is using an original type coil depending on application, then it...
Forum: Early V8 (1932-53) Today, 09:48 AM
Replies: 9
Views: 134
Posted By rotorwrench
Re: Rotors

The early and late 8BA family of engiones as well as the later ford tractors used a flat spring or a clip to fit the rotor tightly to the shaft. These were either the 7RA-12213-B or the 8BA-12213...
Forum: Model A (1928-31) Today, 09:18 AM
Replies: 18
Views: 1,194
Posted By rotorwrench
Re: Scum HAMB Hot Rodder Trying to Save a Truly Wasted Roadster...on YouTube!

I also noticed the missing rivets. They didn't have a lot holding the sill rails to the rear quarter so those two rivets are important. The joint would be a pinch weld point in the modern era but not...
Forum: Early V8 (1932-53) Yesterday, 08:27 AM
Replies: 8
Views: 268
Posted By rotorwrench
Re: 32 amp gauge

Most of the old meters have a little spring to return the needle to center unless it is counter weighted or magnetically centered. The needle may also have slipped on the armature. Many of these...
Forum: Model A (1928-31) Yesterday, 08:10 AM
Replies: 9
Views: 373
Posted By rotorwrench
Re: GAV lever

The model A was made with a lot of manual controls available to the operator. Later cars went on to more automatic type controls as time went by. Few people in the modern era would know how to adjust...
Forum: Early V8 (1932-53) 05-12-2021, 06:48 PM
Replies: 13
Views: 553
Posted By rotorwrench
Re: Pre 1945 Block Cams

The early 99 series till 1941 have the core sand removal ports and associated bulges on the pan rails. The 19A block for 41 was changed some with the abbreviated intake deck area and the lack of...
Forum: Early V8 (1932-53) 05-12-2021, 06:33 PM
Replies: 12
Views: 389
Posted By rotorwrench
Re: 52 F1 tranny

Mac VanPelt's early Ford light duty transmission book is very good. It's a good idea to expect to use a press or some other form of bearing pullers for stubborn parts but the difficult part is...
Forum: Late V8 (1954+) 05-12-2021, 12:42 PM
Replies: 2
Views: 114
Posted By rotorwrench
Re: 1958 Ranch wagon manual transmission parts.

Parts are available but a person needs to know which transmission that parts are needed for. Ford used at least three different 3-speed manual transmissions in that time frame. Mac VP is the go to...
Forum: Model A (1928-31) 05-12-2021, 12:28 PM
Replies: 273
Views: 138,390
Posted By rotorwrench
Re: F150 tranny with overdrive

Those of us that know the Tremec 3&OD transmissions of the 80s will know what to look for but there isn't a lot of information out there on them for the average person who may want one and start...
Forum: Model A (1928-31) 05-12-2021, 10:31 AM
Replies: 18
Views: 1,194
Posted By rotorwrench
Re: Scum HAMB Hot Rodder Trying to Save a Truly Wasted Roadster...on YouTube!

The OPs self discription is likely not warranted on a project like this. Although many folks on the barn are die hard restorers, that doesn't mean that they will scorn the hot rodders. Methods of...
Forum: Model A (1928-31) 05-12-2021, 10:18 AM
Replies: 7
Views: 412
Posted By rotorwrench
Re: AA54XXX VIN Number

In some states, a title that matches no number on engine or frame can be problematic to get registered. I would want to know what the number on the frame is if it is is still visible or can be...
Forum: Early V8 (1932-53) 05-11-2021, 06:58 PM
Replies: 13
Views: 486
Posted By rotorwrench
Re: 35-36 rear into 34

The difference in radius rods may also be worth a mention.
Forum: Early V8 (1932-53) 05-11-2021, 06:51 PM
Replies: 12
Views: 389
Posted By rotorwrench
Re: 52 F1 tranny

If it is the light duty 3-speed of old then the low gear is unsynchronized and slides on the main shaft only when shifted. It either goes into the reverse selection or it goes into 1st gear. If the...
Forum: Model A (1928-31) 05-11-2021, 06:30 PM
Replies: 273
Views: 138,390
Posted By rotorwrench
Re: F150 tranny with overdrive

I don't know about "a lot" but is does share some parts. The RTS or TOD has a lot of its own part numbers compared to the other SROD and SMOD. The SMOD is a lot different and has a cast iron case....
Forum: Model A (1928-31) 05-11-2021, 07:43 AM
Replies: 273
Views: 138,390
Posted By rotorwrench
Re: F150 tranny with overdrive

When Tremec in Mexico stopped production, they likely produced replacement parts for FoMoCo as long as is generally planned. Usually around 10-years. That puts the last of the replacement parts...
Forum: Late V8 (1954+) 05-10-2021, 05:57 PM
Replies: 13
Views: 484
Posted By rotorwrench
Re: Can we post about 1966 Ford Mustangs?

I missed the part about mechanical switch type.

Another place that brake lights can have problems is in the turn signal circuit. The brake lights and turn signals are mixed together through the...
Forum: Model A (1928-31) 05-10-2021, 05:31 PM
Replies: 273
Views: 138,390
Posted By rotorwrench
Re: F150 tranny with overdrive

T-170 RTS hard parts are not easy to come by. Folks generally have to purchase a whole used transmission and hope the parts are still good.
Forum: Late V8 (1954+) 05-10-2021, 09:34 AM
Replies: 13
Views: 484
Posted By rotorwrench
Re: Can we post about 1966 Ford Mustangs?

Either the master cylinder is not letting the pressure off the system or the brake light switch isn't opening the circuit when the pressure drops. I've had problems with both but the clogged up...
Forum: Early V8 (1932-53) 05-10-2021, 09:18 AM
Replies: 5
Views: 316
Posted By rotorwrench
Re: Ford p/u 1946 gearbox

There are a number of wear areas that can contribute to 2nd gear push out. When helical gears became common in the semi-synchronized 3-speed transmissions, the design had to be set up to counter the...
Forum: Model A (1928-31) 05-10-2021, 08:54 AM
Replies: 15
Views: 794
Posted By rotorwrench
Re: Model A Transmission

The A bone transmission is as simple as they get since there are no synchronizers in there. With the exception of some bearings, most parts are reproduced with decent quality. A person has to find...
Forum: Model A (1928-31) 05-10-2021, 08:46 AM
Replies: 273
Views: 138,390
Posted By rotorwrench
Re: F150 tranny with overdrive

To go open drive, it takes more than just modification of the rear axle input. The rear axle will need suspension components to allow it to move but stay in the right place. This generally takes a...
Forum: Late V8 (1954+) 05-09-2021, 10:47 AM
Replies: 13
Views: 377
Posted By rotorwrench
Re: Borg Warner overdrive cable throw position

I'll see if this link comes through for Mac:
http://www.vanpeltsales.com/FH_web/FH_images/Trans%20parts%20pics/VP-7689K-lockoutboltkit.jpg

It would be what you want. Part number VP-7689K.
Forum: Early V8 (1932-53) 05-09-2021, 10:07 AM
Replies: 21
Views: 611
Posted By rotorwrench
Re: 1948 Ford 12 volt coil issues

While there may be myths when referring to human interaction, there are no myths in basic electricity.

When folks speak of internally resisted coils you just need to know that a resistor is a coil...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:30 PM.