Forum: Model A (1928-31)
03-30-2024, 01:28 PM
|
Replies: 15
Views: 1,073
|
Forum: Model A (1928-31)
02-06-2024, 02:48 AM
|
Replies: 22
Views: 1,863
Re: counter balanced crank
I have a Model B crank that is counterweighted. You cut down the mains to Model A size and use a det of B rods..
|
Forum: Model A (1928-31)
01-19-2024, 11:50 PM
|
Replies: 10
Views: 1,378
|
Forum: Model A (1928-31)
12-10-2023, 09:22 PM
|
Replies: 25
Views: 2,560
Re: Balance a Burtz
JayJay, I got my pistons from Leonard Nettles. I believe they are Silvolite.
|
Forum: Model A (1928-31)
12-10-2023, 01:35 PM
|
Replies: 25
Views: 2,560
Re: Balance a Burtz
I'm going to send my Burtz engine parts to the balancer. Going to start my build first of the year. I'll report the results.
|
Forum: Model A (1928-31)
10-11-2023, 12:08 PM
|
Replies: 55
Views: 14,875
|
Forum: Model A (1928-31)
09-29-2023, 08:23 AM
|
Replies: 14
Views: 1,398
|
Forum: Model A (1928-31)
09-08-2023, 08:34 PM
|
Replies: 38
Views: 3,851
Re: mitchell O/D
Yes, Leave a message and Steve will call you back. I'm on the wait list about a month now so I'll hear from them next year.
|
Forum: Model A (1928-31)
08-09-2023, 02:44 PM
|
Replies: 36
Views: 8,446
Re: New Engine from Todd?
BRENT in 10-uh-C,
Thanks for that information. I did not think of, nor did I realize I would be compromising the hardness of the crank. I'll check with the person that did the Babbitt and see what...
|
Forum: Model A (1928-31)
08-09-2023, 12:39 AM
|
Replies: 36
Views: 8,446
Re: New Engine from Todd?
Synchro909, the "B" crank I have had already been machined quite a bit. So going to Model A size was no worry. I cut the mains down to 1.625. The crank still has the thicker casting and as cast...
|
Forum: Model A (1928-31)
08-08-2023, 02:25 PM
|
Replies: 36
Views: 8,446
Re: New Engine from Todd?
Making the larger main bearing caps is yes expensive time consuming. The real work is machining the block to match. Solution is grinding the "B" crank main bearings to "A" crank size and go from...
|
Forum: Model A (1928-31)
05-18-2023, 10:55 PM
|
Replies: 43
Views: 6,743
Re: Mitchell overdrive.
I ordered my overdrive end of June 2022. I received it mid April 2023.
I had forgot all about it, and then a surprise phone call from Steve and he says your name is at the top of the list. Time to...
|
Forum: Model A (1928-31)
02-22-2023, 09:08 AM
|
Replies: 18
Views: 2,739
|
Forum: Model A (1928-31)
01-25-2023, 03:43 AM
|
Replies: 22
Views: 4,047
Re: Now What
Did a Bendix bolt fall out of the starter and jam the flywheel?
|
Forum: Model A (1928-31)
12-30-2022, 09:13 AM
|
Replies: 18
Views: 2,830
|
Forum: Model A (1928-31)
12-04-2022, 01:49 AM
|
Replies: 12
Views: 1,514
|
Forum: Model A (1928-31)
12-02-2022, 05:33 PM
|
Replies: 99
Views: 29,706
|
Forum: Model A (1928-31)
11-30-2022, 09:02 AM
|
Replies: 99
Views: 29,706
|
Forum: Model A (1928-31)
11-29-2022, 12:36 PM
|
Replies: 38
Views: 7,277
Re: Head Gasket Failure & Replacement Saga
Interesting info about backing off the head nuts before retorquing.
My Snyder head 6.1 had to have right at .006 taken off to get flat. I also had my block surfaced flat so hopefully I won't have...
|
Forum: Model A (1928-31)
11-03-2022, 12:10 PM
|
Replies: 19
Views: 3,800
|
Forum: Model A (1928-31)
11-01-2022, 12:52 PM
|
Replies: 19
Views: 3,800
Re: Burtz Flywheel
Terry, I understand the effects of the heavier weight. However, I'm not building my motor for speed or racing. It should work just fine for cruising and touring.
What about adding a harmonic...
|
Forum: Model A (1928-31)
11-01-2022, 12:09 PM
|
Replies: 6
Views: 2,176
Re: Terry Burtz rear main seal
Did you screw the oil return pipe too far into the rear main cap? If so, it will block the oil passage and result in a leak. I did that and had a huge oil leak.
|
Forum: Model A (1928-31)
10-29-2022, 02:59 PM
|
Replies: 19
Views: 3,800
Re: Burtz Flywheel
How about some thoughts on using a stock weight flywheel/clutch with the New Burtz engine.
|
Forum: Model A (1928-31)
10-18-2022, 06:57 PM
|
Replies: 26
Views: 5,035
Re: A question about colors
I think the latest Paint & finish guide from MAFCA is the way to go. It has much larger paint chip samples in it.
|
Forum: Model A (1928-31)
10-18-2022, 02:07 PM
|
Replies: 74
Views: 34,493
|