Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 12 of 12
Search took 0.00 seconds.
Search: Posts Made By: Twrench~70
Forum: Early V8 (1932-53) 10-03-2021, 09:23 AM
Replies: 2
Views: 201
Posted By Twrench~70
Re: 1938 60 HP Drive shaft

No I was just wondering about the center support bearing. Not too worried about the length. Thank you cas3
Forum: Early V8 (1932-53) 10-02-2021, 06:22 PM
Replies: 2
Views: 201
Posted By Twrench~70
1938 60 HP Drive shaft

Could someone enlighten me if all drive shafts for torgue tubes are the same diameter or is the infamous 60hp drive shaft a smaller diameter. Thank you
Forum: Early V8 (1932-53) 09-18-2021, 02:11 PM
Replies: 4
Views: 328
Posted By Twrench~70
Re: 1938 windshield seal

Thanks for the heads up about the channel. soap and clean of rust and old seals.
Forum: Early V8 (1932-53) 09-17-2021, 02:39 PM
Replies: 4
Views: 328
Posted By Twrench~70
1938 windshield seal

Could someone help me about a 38 windshield frame seal. I have a B.Drake one and it seems like a real struggle to seat it. Any help would be appreciated.
Forum: Early V8 (1932-53) 03-05-2021, 10:16 PM
Replies: 18
Views: 1,178
Posted By Twrench~70
Re: 1938 ford standard 60 hp motor

I don't want to take them out I just want to know they rotate???/ Right hand thread or left hand thread to open them up. thank you
Forum: Early V8 (1932-53) 03-05-2021, 06:23 PM
Replies: 18
Views: 1,178
Posted By Twrench~70
Re: 1938 ford standard 60 hp motor

There is no drain cock on the radiator ford38v8. there is only two petcocks under the heads toward the front of the motor. Thank you for your reply
Forum: Early V8 (1932-53) 03-05-2021, 04:37 PM
Replies: 18
Views: 1,178
Posted By Twrench~70
1938 ford standard 60 hp motor

I would like to know if the petcocks on either side of the motor for coolant drain is a right hand or a left hand thread. Doing a head gasket replacement and I need to drain the motor. Or should I...
Forum: Early V8 (1932-53) 04-26-2020, 01:13 PM
Replies: 7
Views: 901
Posted By Twrench~70
Forum: Early V8 (1932-53) 04-26-2020, 10:27 AM
Replies: 7
Views: 901
Posted By Twrench~70
1938 Ford standard trans lube and rear end lube

Hello everyone, I was wondering what lubricant I should use in my 38 Standard witn a 60hp 3 speed transmission. Should I use 600w oil or the modern version of gear oil-85/140 w. Thank you
Forum: Early V8 (1932-53) 03-20-2020, 05:07 PM
Replies: 5
Views: 824
Posted By Twrench~70
Re: 1938 Ford standard clutch assy.

parts availability thats all. I can get it fixed but its way too costly. thank you for the reply Kurt.
Forum: Early V8 (1932-53) 03-20-2020, 02:03 PM
Replies: 5
Views: 824
Posted By Twrench~70
1938 Ford standard clutch assy.

guys, I was wondering if it's possible to change a clutch for a 60hp motor that comes with a 8.5 clutch to a 9 inch clutch and pressure plate assembly. this one is giving me fits as to what to do....
Forum: Early V8 (1932-53) 02-25-2020, 01:47 PM
Replies: 21
Views: 1,706
Posted By Twrench~70
Engine swap

Hey guys, I was just wondering if this question has been answer...? Probably a hundred or so. I own a 38 standard Tudor with a 60 H.P flattie and I was wondering if it would be a lot of altering to...
Showing results 1 to 12 of 12

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:03 AM.