Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 21 of 21
Search took 0.00 seconds.
Search: Posts Made By: f balsiger
Forum: Model A (1928-31) 11-13-2020, 01:47 PM
Replies: 2
Views: 356
Posted By f balsiger
adapting a ford pickup steering gear to model a

looking for a kit to put newer ford steering box in my model A.
Forum: Model A (1928-31) 11-12-2020, 01:57 PM
Replies: 4
Views: 382
Posted By f balsiger
adapting a ford pickup steering gear to model a

where can I find a kit to do this?
Forum: Model A (1928-31) 11-12-2020, 01:22 PM
Replies: 11
Views: 505
Posted By f balsiger
2 tooth adjustment

I dont under stand how the adjustments work in agemmer two tooth steering gear.
Forum: Model A (1928-31) 08-08-2020, 05:26 PM
Replies: 13
Views: 635
Posted By f balsiger
Re: 12v amps gauge

ok reverse wires. alternator goes to +?
Forum: Model A (1928-31) 08-08-2020, 08:10 AM
Replies: 13
Views: 635
Posted By f balsiger
12v amps gauge

can I use a stock 6v amps gauge in 12v neg ground system?
Forum: Model A (1928-31) 12-06-2019, 06:16 PM
Replies: 3
Views: 834
Posted By f balsiger
zenith 1

what does the cap jet do? there is a main jet for high speed. does the idle adjustment screw only control air? If so how does fuel get to the throat at Idle?
Forum: Model A (1928-31) 11-26-2019, 12:02 PM
Replies: 41
Views: 2,230
Posted By f balsiger
12 volt coil with resistor

will a 12v coil with resistor send 12v to the points? I don't understand if the resistor lowers voltage or ohms
Forum: Model A (1928-31) 11-26-2019, 11:56 AM
Replies: 11
Views: 1,099
Posted By f balsiger
Re: parts for tillotson

[QUOTE=f balsiger;1824829]where can I get a rebuild kit for tillotson round bowl carburetor (f1-B)
Forum: Model A (1928-31) 11-24-2019, 01:56 PM
Replies: 11
Views: 1,099
Posted By f balsiger
parts for tillotson

where can I get a rebuild kit for tillotson round bowl carburetor
Forum: Model A (1928-31) 11-13-2019, 07:18 PM
Replies: 15
Views: 1,281
Posted By f balsiger
Re: engine misses

found problem , so called modern points had intermittent short in lower portion.
Forum: Model A (1928-31) 11-02-2019, 02:59 PM
Replies: 15
Views: 1,281
Posted By f balsiger
engine misses

engine misses at all speeds. good compression which I think eliminates valves , no vacuum leaks (intake) tends to blubber. Almost goes away with full retard on timing. New modern point and condenser....
Forum: Model A (1928-31) 09-11-2019, 04:26 PM
Replies: 11
Views: 905
Posted By f balsiger
Re: zenith 1 overflows.

the leak is a study stream leading me to believe it has to be float valve. the flow is from the hole near the bowl air vent. I have tried 2 additional float and valve combinations same problem...
Forum: Model A (1928-31) 09-10-2019, 01:44 PM
Replies: 11
Views: 905
Posted By f balsiger
zenith 1 overflows.

my zenith carb overflows out the hole on the opposite side from the intake. I have installed a new needle valve and have lowered the float over I/8 inch and made sure the valve sealed manually.
I...
Forum: Model A (1928-31) 08-24-2019, 07:44 AM
Replies: 10
Views: 1,133
Posted By f balsiger
Re: wierd noise in engine

thanks for the info!
Forum: Model A (1928-31) 08-22-2019, 07:11 AM
Replies: 10
Views: 1,133
Posted By f balsiger
wierd noise in engine

When I first start the engine some thing knocks until the oil is up (2 min.) Then when the spark is advanced there is an occasional CLANK! I put in a new cam spring.
Could this be the distributor...
Forum: Model A (1928-31) 08-17-2019, 12:56 PM
Replies: 4
Views: 709
Posted By f balsiger
crank gear

my crank gear has 2 timing marks?
Forum: Model A (1928-31) 08-13-2019, 02:09 PM
Replies: 8
Views: 1,216
Posted By f balsiger
Question model a engine jumps time

checked distributor drive gear....ok camshaft next?
Forum: Model A (1928-31) 04-03-2019, 11:51 AM
Replies: 2
Views: 547
Posted By f balsiger
wrist pin bushings

how does oil get to the wrist pins?
Forum: Model A (1928-31) 03-30-2019, 01:43 PM
Replies: 5
Views: 642
Posted By f balsiger
wrist pin bushings

I am confused , what holes do I drill in a wrist pin bushing?
Forum: Model A (1928-31) 09-25-2018, 05:24 PM
Replies: 5
Views: 936
Posted By f balsiger
Re: engine swap

It will bolt up?
Forum: Model A (1928-31) 09-25-2018, 11:50 AM
Replies: 5
Views: 936
Posted By f balsiger
engine swap

will a model B engine fit in a model A?
Showing results 1 to 21 of 21

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:30 PM.