Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 48
Search took 0.01 seconds.
Search: Posts Made By: Ideucev8
Forum: Early V8 (1932-53) 11-23-2021, 02:05 PM
Replies: 22
Views: 823
Posted By Ideucev8
Re: 39 Brake Questions.

Your spindles are not 38 they must be 35-36 All spindles from 37 on have that big centre hole & larger bolt holes. These will take all take 39 on backing plates.
Phil.
Forum: Early V8 (1932-53) 11-01-2021, 10:14 PM
Replies: 14
Views: 420
Posted By Ideucev8
Re: 34 Ford Pickup - Intermittent Spark

That distributor looks like it needs a good rebuild. The cam looks rusty with no grease on it. The rubbing blocks may have worn down from the rusty dry cam and the point gap closed up. I would send...
Forum: Early V8 (1932-53) 10-28-2021, 01:58 PM
Replies: 918
Views: 65,099
Posted By Ideucev8
Re: 1932 The Deuce, Dually, Dump Truck

Your Headlight lens with the indentations is a 33/34 lens. just bend up some clips to suit.
Phil.
Forum: Early V8 (1932-53) 09-15-2021, 03:05 PM
Replies: 9
Views: 512
Posted By Ideucev8
Re: red fuel gauge liquid: old vs. newer

Has any one tried this liquid? https://www.ebay.com/itm/185050510369?hash=item2b15deb421:g:oJEAAOSwKIBfxVRF
Forum: Early V8 (1932-53) 09-02-2021, 06:19 PM
Replies: 3
Views: 312
Posted By Ideucev8
Re: 1932-1934 pickup window channel installation questions

Hi, the hook end is the top. I had to bend the hook out at right angles to the channel then insert the bottom end into the hole & pull the channel up. then bend the hook over at the top. Mine were...
Forum: Early V8 (1932-53) 08-23-2021, 04:24 PM
Replies: 19
Views: 2,625
Posted By Ideucev8
Re: temperature gauge for 1933

Hi. John rennerscorner.com have the gas gauge parts.
Phil.
Forum: Early V8 (1932-53) 07-28-2021, 10:30 PM
Replies: 17
Views: 1,250
Posted By Ideucev8
Re: 35 Ford pickup grille

As Brian said , they were mounted on to the radiator side straps on my 35 Pickup.
Phil.
Forum: Early V8 (1932-53) 07-19-2021, 06:21 PM
Replies: 12
Views: 924
Posted By Ideucev8
Re: Speedo drive gear

I have just checked an original 34 rear end & torque tube assy that I have, & the speedo drive gear has about 3/16" of movement back & forward on the spline.
It appears to have an even amount of...
Forum: Early V8 (1932-53) 07-18-2021, 04:19 AM
Replies: 11
Views: 607
Posted By Ideucev8
Re: 8ba Inlet Manifold Under carb Vacuum.

Just looked at 2 8BA manifolds I have here & they both have the holes drilled to both sides.
Phil
Forum: Early V8 (1932-53) 07-15-2021, 03:11 PM
Replies: 74
Views: 4,218
Posted By Ideucev8
Re: Hydraulic brake questions - 1932 Coupe

Hi is it like this one? https://www.jalopyjournal.com/forum/threads/new-1932-model-a-k-members.1235543/

Phil
Forum: Early V8 (1932-53) 05-29-2021, 04:14 PM
Replies: 8
Views: 607
Posted By Ideucev8
Re: '39 - '48 Master Cyl...rear hyds on a '32

Hi Charlie,
Yes you will have trouble getting the air out of the rear wheel cylinders. I have had trouble with bleeding the rear brakes on two 32s & some 34s with rotated backing...
Forum: Early V8 (1932-53) 11-13-2020, 06:54 AM
Replies: 5
Views: 444
Posted By Ideucev8
Re: '34-36 headlight bulb sockets ?

They look like 32 with that plug on the other end of the wires.
Phil.
Forum: Early V8 (1932-53) 11-02-2020, 07:11 AM
Replies: 70
Views: 5,785
Posted By Ideucev8
Re: 1932 V8 standard roadster update

David,
Thanks for that, great idea.
Phil
Forum: Early V8 (1932-53) 11-01-2020, 07:38 AM
Replies: 70
Views: 5,785
Posted By Ideucev8
Re: 1932 V8 standard roadster update

David

Thanks for your reply to my question about the license lamp lens. I have your two 32 books so knew about the tail lamp housings. That red lens is a great way to get around it & use a...
Forum: Early V8 (1932-53) 10-27-2020, 03:24 PM
Replies: 70
Views: 5,785
Posted By Ideucev8
Re: 1932 V8 standard roadster update

David, it appears that the license plate lamp lens is red in the RH tail lamp. Was the dealer installed second tail lamp supplied like this?
Phil.
Forum: Early V8 (1932-53) 10-27-2020, 07:31 AM
Replies: 70
Views: 5,785
Posted By Ideucev8
Re: 1932 V8 standard roadster update

Wow that is great, very well done. I hope you will post some more photos of it.
Forum: Early V8 (1932-53) 10-23-2020, 07:13 PM
Replies: 10
Views: 756
Posted By Ideucev8
Re: Banjo pinion removal tool

Yes I have been doing it that way for over 50 years.
Forum: Early V8 (1932-53) 10-09-2020, 05:55 PM
Replies: 75
Views: 5,062
Posted By Ideucev8
Re: Question on Cam Gear Marks - UPDATE

I would remove the cam gear & rotate the crankshaft the one tooth as it would be much easier to turn than turning the camshaft.
Phil
Forum: Early V8 (1932-53) 10-01-2020, 07:36 PM
Replies: 3
Views: 596
Posted By Ideucev8
Re: 1932 Ford V8 front motor mounts??

Hi yes they are. Back Order Bob Drake & he has them in stock.
Phil.
Forum: Early V8 (1932-53) 09-20-2020, 07:27 AM
Replies: 13
Views: 1,033
Posted By Ideucev8
Re: 8BA fuel pump pushrod diameter

Just checked 2 NOS 8BA push rods in some NOS bushings & they are quite loose. I have just fitted some of these parts in a 8BA I have just rebuilt & they are no tighter than the ones I took out.
Phil.
Forum: Early V8 (1932-53) 08-30-2020, 10:37 PM
Replies: 32
Views: 1,911
Posted By Ideucev8
Re: Hydraulic Brakes 39 Ford.

You have to have free travel at your brake pedal for the master cylinder to work properly, to let he pressure out of the system. the brake pedal should move 3/4" before the push rod moves the master...
Forum: Early V8 (1932-53) 08-11-2020, 04:44 PM
Replies: 8
Views: 528
Posted By Ideucev8
Re: 36 pickup dash light switch

Hi yes they do have a dash light switch. It mounts on the lower edge of the dash. It is a small toggle type switch with a small round shaft. There should be a larger hole with 2 small holes each side...
Forum: Early V8 (1932-53) 08-07-2020, 08:42 AM
Replies: 9
Views: 1,174
Posted By Ideucev8
Re: C69A block

Lawrie, Re engine stay rods to 8ba. I have done this a few times over the last 50 or so years to 35s 36s & just done a 32.
The bottom two bolts holding the 8ba bellhousing to the block are inline...
Forum: Early V8 (1932-53) 07-31-2020, 10:56 PM
Replies: 13
Views: 1,326
Posted By Ideucev8
Re: There must be a better way

The Brillman solder on terminals are much shorter & let the cable bend right in by the terminal plate.
Phil
Forum: Early V8 (1932-53) 04-29-2020, 09:25 PM
Replies: 20
Views: 2,073
Posted By Ideucev8
Re: Oil slinger, crank snout, crank sleeve.

The same slinger is used from about 1939 through to the 8BAs & as the seal sleeve was part of the front pulley on the pre 8BAs you could slide the slinger off & on with the key in place.
Phil
Showing results 1 to 25 of 48

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:31 AM.