Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.07 seconds.
Search: Posts Made By: G.M.
Forum: Early V8 (1932-53) 02-24-2021, 02:15 PM
Replies: 169
Views: 4,852
Posted By G.M.
Forum: Early V8 (1932-53) 02-12-2021, 11:18 AM
Replies: 31
Views: 1,278
Posted By G.M.
Re: Block leak help, Lending a hand!!!

What are technical epoxies?? G.M.
Forum: Early V8 (1932-53) 02-11-2021, 02:58 PM
Replies: 31
Views: 1,278
Posted By G.M.
Re: Block leak help, Lending a hand!!!

Barr's stop leak with copper particals has stopped any leaks
I have had. G.M.
Forum: Early V8 (1932-53) 01-31-2021, 02:15 PM
Replies: 31
Views: 1,544
Posted By G.M.
Re: Runs great until it heats up

What is the voltage at the coil, points open and points closed. G.M.
Forum: Early V8 (1932-53) 01-25-2021, 09:33 PM
Replies: 9
Views: 598
Posted By G.M.
Re: Holley 94 jetting question

I use an exhaust anolyzer in the exhaust pipe and
change jet sizes until it is close to perfect. G.M.
Forum: Early V8 (1932-53) 01-24-2021, 08:34 AM
Replies: 26
Views: 1,004
Posted By G.M.
Re: '35 Radiator / water out the tube

I am not pressurizing the system at less than 4 lbs. 4 lbs is the cap
ratting not the pressure in the system. Most water pumps slip and
churn air into the mixture. Air does not cool like water....
Forum: Early V8 (1932-53) 01-23-2021, 01:49 PM
Replies: 26
Views: 1,004
Posted By G.M.
Re: '35 Radiator / water out the tube

With a pressure cap and a recovery bottle you can fill the
radiator up into the filler neck. More coolant, better cooling.
G.M.
Forum: Early V8 (1932-53) 01-22-2021, 11:51 PM
Replies: 26
Views: 1,004
Posted By G.M.
Re: '35 Radiator / water out the tube

You need to let as MUCH coolant flow though the radiator as possible.
Why did you put on high flow pumps and want to slow the flow? You
need a pressure cap and a recovery bottle. As the engine...
Forum: Early V8 (1932-53) 01-22-2021, 11:17 PM
Replies: 52
Views: 3,211
Posted By G.M.
Re: Calling Ol'Ron, calling Ol'Ron...

New springs need to be tested and exter shims may be needed
to get the springs to the same pressure at normal spring height.
There is a machine just for this. I have one. If you get to Florida
...
Forum: Early V8 (1932-53) 01-22-2021, 10:31 AM
Replies: 15
Views: 656
Posted By G.M.
Re: 1935 Hydrostatic Sending Unit

Years ago I posted on this site how to rebuild the
Hydrostatic sending unit. I have done 5 or 6 and
they all worked good. You have to be VERY careful
with the soldering that you don't plug...
Forum: Early V8 (1932-53) 01-22-2021, 10:23 AM
Replies: 52
Views: 3,211
Posted By G.M.
Re: Calling Ol'Ron, calling Ol'Ron...

You don't just stick .060 shims under warn weak
springs. There is a spring test machine that shows
the spring pressure at a set height. They should
all be close to the same pressure. G.M.
Forum: Early V8 (1932-53) 01-21-2021, 01:11 PM
Replies: 23
Views: 1,091
Posted By G.M.
Re: MiG help

That's very hard to believe. G.M.
Forum: Early V8 (1932-53) 01-21-2021, 01:07 PM
Replies: 22
Views: 1,200
Posted By G.M.
Re: Who can repair the fuel sending units

I think Charley in N.Y. does them. G.M;
Forum: Early V8 (1932-53) 01-21-2021, 01:05 PM
Replies: 8
Views: 417
Posted By G.M.
Re: 1946 Mercury exhaust system source?

I think the Mercury caris longer than the Ford. I had the drive
shaft and rear from a 1948 Mercury and it was 8 or so inches
longer. G.M.
Forum: Early V8 (1932-53) 01-20-2021, 04:44 PM
Replies: 8
Views: 417
Posted By G.M.
Re: 1946 Mercury exhaust system source?

I think Ford pipes will work but need to be lengthend
at the mufflers. G.M.
Forum: Early V8 (1932-53) 01-20-2021, 04:37 PM
Replies: 6
Views: 501
Posted By G.M.
Re: Wrong fuel pump?

The only problem is a 30 year old pump rubber diaphram will
will be bad or wrong material and need to be replaced. G.M.
Forum: Early V8 (1932-53) 01-20-2021, 04:28 PM
Replies: 23
Views: 1,091
Posted By G.M.
Re: MiG help

Loosen the drive wheel, remove contact tip and cut
wire off so 1/4'' sticks out the rear of the tip. Go to
your grinding wheel and grind about 1/16" off the
front of the tip where the wire is...
Forum: Early V8 (1932-53) 01-15-2021, 10:09 AM
Replies: 9
Views: 1,010
Posted By G.M.
Re: Clutch chatter solved!

When I was a kid 75 years ago we swipped a fire xting and
squirted carbon teck in trough the trany inspection plate
and with the front bumper against a tree slipped the clutch.
That usually worked...
Forum: Early V8 (1932-53) 01-13-2021, 08:24 PM
Replies: 8
Views: 671
Posted By G.M.
Re: 42-48 coil cores have any value? Script.

Skip can always good cores. Make a deal to have one rebuilt
and use the others to off set cost. G.M.
Forum: Early V8 (1932-53) 01-05-2021, 06:53 PM
Replies: 18
Views: 1,009
Posted By G.M.
Re: 12 Volt battery to fit '40

How about an Optima?? G.M.
Forum: Early V8 (1932-53) 01-05-2021, 06:51 PM
Replies: 24
Views: 1,038
Posted By G.M.
Re: Generator Pulley Missing Coolaing Vanes

I would say they broke upon installation. G.M.
Forum: Early V8 (1932-53) 01-04-2021, 03:47 PM
Replies: 9
Views: 519
Posted By G.M.
Re: 39 Standard Generator to 12V

The 24 volt stator was suggested Chestnut Hill Electric Motor Co
so it would charge at idle with a small pulley. They have all the
parts in stock. located in Denver. Pa. G.M.
Forum: Early V8 (1932-53) 01-03-2021, 02:13 PM
Replies: 8
Views: 613
Posted By G.M.
Re: 3.55 rear end ratio

I have a 3:55 rear in of my 39 convertibles. Powered by one
of the brand new Canadian truck engines available over 40
years ago. Very seldom had to down shift for a hill. I ran it
from S W Florida...
Forum: Early V8 (1932-53) 01-03-2021, 01:36 PM
Replies: 9
Views: 519
Posted By G.M.
Re: 39 Standard Generator to 12V

If you don't mind the appearance this GM alt really
works great. You should have a 24 volt stator installed
so you can run the small stock pulley. With this it will
idle with the lights on and...
Forum: Early V8 (1932-53) 01-03-2021, 01:24 PM
Replies: 6
Views: 346
Posted By G.M.
Re: 34 electrical issues and 8V->6V conversion

It won't start with 2.6 volts to the coil. It drops even lower
when the starter is running. A 6 volt Optima battery will
fit in you box. You need a minimum of 3.5 and max of 4.2
8 volt batteries...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:46 AM.