Forum: Early V8
07-20-2021, 07:35 PM
|
Replies: 0
Views: 520
V-126 Wanted
Looking for a V-126 distributor timing fixture. Thanks Wayne
|
Forum: Model A (1928-31)
09-09-2019, 09:15 PM
|
Replies: 16
Views: 2,329
Re: Engine Oil consumption
I do not see any smoke out the exhaust. I do see a small drip on the transmission plug thought. No blow-by from the filler either. I thought I read somewhere that due to the splashing of the oil on...
|
Forum: Model A (1928-31)
09-09-2019, 06:22 PM
|
Replies: 16
Views: 2,329
|
Forum: Model A (1928-31)
09-09-2019, 05:29 PM
|
Replies: 16
Views: 2,329
Engine Oil consumption
Just interested in how much oil is used up in a decent engine? Lets say 65psig for compression in each cylinder and very few leaks. I know there are lots of variables. My engine has roughly 45,000...
|
Forum: Model A (1928-31)
06-25-2018, 09:40 PM
|
Replies: 4
Views: 1,316
|
Forum: Model A (1928-31)
06-24-2018, 05:03 PM
|
Replies: 4
Views: 1,316
Model A Ignition switch Types
Did all Model As come with the pop out ignition switch or did they come with a turn key type with wires to the distributor? I realize the ignition wire is or should I say as I always see them exiting...
|
Forum: Model-A
06-16-2018, 08:43 PM
|
Replies: 0
Views: 944
|
Forum: Model-A
06-15-2018, 06:10 PM
|
Replies: 0
Views: 815
|
Forum: Model A (1928-31)
05-01-2018, 07:58 PM
|
Replies: 14
Views: 5,734
Re: Excess runout on flywheel
Al,
I just went through this issue with my 1930. However, there was a paper published in the Restorers Journal addressing the issue. The author states the motor should be out of the car on an...
|
Forum: Model A (1928-31)
12-13-2017, 01:34 PM
|
Replies: 8
Views: 1,480
Re: 1930 fordor bottom gasket install
Norm,
Yes the seal is held in place behind the door panel with small head nails. However, looking at the picture dike36 sent, I do not see an h shaped seal. I wonder if the seal in the...
|
Forum: Model A (1928-31)
12-12-2017, 08:43 PM
|
Replies: 8
Views: 1,480
Re: 1930 fordor bottom gasket install
Hi Paul,
I can not see any prongs. Looks like the old panel was tacked in along the bottom. I did pull back the bottom of the panel though. Actually had the old panel off to replace the...
|
Forum: Model A (1928-31)
12-12-2017, 01:31 PM
|
Replies: 8
Views: 1,480
Re: 1930 fordor bottom gasket install
I got the parts from TAMS in MASS. I know there is something there because I pulled off some old rubber underneath the door panel at the bottom. Looks like I will have to play with it awhile.
|
Forum: Model A (1928-31)
12-11-2017, 07:56 PM
|
Replies: 8
Views: 1,480
1930 fordor bottom gasket install
I have read the posts on this subject here but have not read a detailed instruction on the bottom door seal for a 1930 fordor 170B. Never did this before. I have the "h" seal. how do I hang it and...
|
Forum: Model A (1928-31)
11-22-2017, 01:40 PM
|
Replies: 15
Views: 1,646
|
Forum: Model A (1928-31)
11-22-2017, 01:28 PM
|
Replies: 15
Views: 1,646
|
Forum: Model A (1928-31)
11-22-2017, 12:12 PM
|
Replies: 15
Views: 1,646
|
Forum: Model A (1928-31)
11-21-2017, 11:47 PM
|
Replies: 15
Views: 1,646
|
Forum: Model A (1928-31)
11-21-2017, 11:45 PM
|
Replies: 15
Views: 1,646
|
Forum: Model A (1928-31)
11-21-2017, 10:09 PM
|
Replies: 15
Views: 1,646
|
Forum: Model A (1928-31)
11-21-2017, 09:49 PM
|
Replies: 15
Views: 1,646
|