Forum: Model A (1928-31)
12-16-2022, 04:49 PM
|
Replies: 44
Views: 14,872
Re: Whats up with Ecklers
I thought I would add my experience with Ecklers independent of all previous comments.
I have purchased quite a bit of merchandise from them over the past 20 years. They had great catalogs. ...
|
Forum: Model A (1928-31)
12-05-2022, 03:39 PM
|
Replies: 71
Views: 10,217
Re: Supercharging a Model A
GeneBob, is your Cling's crank pulley a one-piece and is it steel or aluminum? I have not installed my own Cling's crank pulley because it is two-piece with the inner part steel and the outer pulley...
|
Forum: Model A (1928-31)
10-30-2022, 04:04 PM
|
Replies: 47
Views: 7,807
Re: Banger Fuel Injection
Electronic fuel injection is complicated. Therefore, case studies are needed to get past the assorted hurdles, physical and psychological. Car magazines have been supplying such stories for quite a...
|
Forum: Model A (1928-31)
07-24-2022, 03:42 PM
|
Replies: 28
Views: 5,240
Re: Disc brakes
I am wondering how to have disk brakes on the front axle while using 5-on-5 1/2 bolt circle wheels. I need how to do it advice.
|
Forum: Model A (1928-31)
06-19-2022, 05:00 AM
|
Replies: 11
Views: 1,242
|
Forum: Model A (1928-31)
06-18-2022, 03:09 PM
|
Replies: 8
Views: 1,262
Model B distributor rebuild
I know how to change the main shaft bushings in a Model B distributor. I need to know how to take the slop out of a worn advance mechanism. The tube to which the cam attaches is sloppy on its pin...
|
Forum: Model A (1928-31)
06-15-2022, 05:24 PM
|
Replies: 10
Views: 1,408
|
Forum: Model A (1928-31)
06-15-2022, 11:28 AM
|
Replies: 10
Views: 1,408
distributor bushing source?
I have not been able to find a source for the thin wall distributor bushings. Oilite bushings with a 9/16 od and 1/2 id is what seems to be needed.
|
Forum: Model A (1928-31)
06-01-2022, 06:03 AM
|
Replies: 27
Views: 8,686
|
Forum: Model A (1928-31)
05-31-2022, 04:10 PM
|
Replies: 27
Views: 8,686
Effect of too large point gap
Thought I'd pass on a lesson learned about points gaps. I was having a devil of a time tracing the cause of engine misfire > 1900 rpm with my Burtz engine set up with a stock head and Model B...
|
Forum: Model A (1928-31)
05-13-2022, 07:42 AM
|
Replies: 7
Views: 2,229
Re: Distributor rotation direction
My Model B distributors seem to display too much variation even when nicely rebuilt. An FSI setup is super expensive. I do not see how I can reverse the Mallory Chevrolet distributor's rotation...
|
Forum: Model A (1928-31)
05-12-2022, 05:58 PM
|
Replies: 7
Views: 2,229
Distributor rotation direction
What car's distributor can be adapted to a Model A/B engine for CCW rotation and have the advance mechanism work correctly?
|
Forum: Model A (1928-31)
01-13-2022, 08:11 AM
|
Replies: 531
Views: 262,469
|
Forum: Model A (1928-31)
12-25-2021, 09:32 AM
|
Replies: 531
Views: 262,469
|
Forum: Model A (1928-31)
12-23-2021, 04:49 PM
|
Replies: 531
Views: 262,469
|
Forum: Model A (1928-31)
12-19-2021, 07:23 AM
|
Replies: 531
Views: 262,469
|
Forum: Model A (1928-31)
12-18-2021, 03:47 PM
|
Replies: 531
Views: 262,469
|
Forum: Model A (1928-31)
12-18-2021, 07:51 AM
|
Replies: 531
Views: 262,469
|
Forum: Model A (1928-31)
12-16-2021, 05:02 PM
|
Replies: 531
Views: 262,469
|
Forum: Model A (1928-31)
11-30-2021, 04:50 PM
|
Replies: 531
Views: 262,469
|
Forum: Early V8 (1932-53)
10-17-2021, 04:30 PM
|
Replies: 0
Views: 782
Cross steering lessons with Unisteer
I have two Unisteer installations on a lowered 1934 truck and a 1924 Track T style hotrod with Model A power. I was lucky on the 34 to get critical dimensions correct from the outset, but on the...
|
Forum: Model A (1928-31)
10-17-2021, 03:35 PM
|
Replies: 531
Views: 262,469
|
Forum: Model A (1928-31)
10-17-2021, 03:34 PM
|
Replies: 531
Views: 262,469
|
Forum: Model A (1928-31)
10-09-2021, 06:26 AM
|
Replies: 39
Views: 6,586
|
Forum: Model A (1928-31)
09-01-2021, 12:30 PM
|
Replies: 24
Views: 5,357
Re: OHV build just about wrapped up.
John, in my research of pent-roof heads for A/B/C engines I have found the front and back cylinder head bolt locations on the driver (left) side quite a challenge compared to the front and back...
|