Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 384
Search took 0.02 seconds.
Search: Posts Made By: Yoyodyne
Forum: Early V8 (1932-53) 11-22-2020, 11:19 AM
Replies: 37
Views: 1,486
Posted By Yoyodyne
Re: Big Boys Heads

B&S - Wow, beautiful parts.
Forum: Early V8 (1932-53) 11-21-2020, 09:23 AM
Replies: 32
Views: 1,547
Posted By Yoyodyne
Re: head stud removal

Thanks Frank, that's hard info to come by, and important.
Forum: Early V8 (1932-53) 11-20-2020, 08:01 PM
Replies: 32
Views: 1,547
Posted By Yoyodyne
Re: head stud removal

Makes sense.
Forum: Early V8 (1932-53) 11-20-2020, 07:59 PM
Replies: 32
Views: 1,547
Posted By Yoyodyne
Re: head stud removal

The way I did it with the bushing in the head was almost that fast, definitely would be next time when I don't have to experiment and feel my way. I had no way to determine the exact center of the...
Forum: Early V8 (1932-53) 11-18-2020, 07:24 PM
Replies: 32
Views: 1,547
Posted By Yoyodyne
Re: head stud removal

I just did battle with the studs on a 36 LB block. The studs were crusty from sitting with the heads off and being roughly handled so I didn't care about saving them. I'm gunshy about heating any...
Forum: Early V8 (1932-53) 11-18-2020, 01:52 PM
Replies: 32
Views: 1,547
Posted By Yoyodyne
Re: head stud removal

What size tip do you use?
Forum: Early V8 (1932-53) 11-06-2020, 09:23 AM
Replies: 25
Views: 1,220
Posted By Yoyodyne
Re: Stuck block two questions

One more thing - Don't put any aluminum or other non-ferrous metals in the sodium hydroxide. The part will either be damaged or won't be there when you go back for it, plus it will crud up your...
Forum: Early V8 (1932-53) 11-06-2020, 03:57 AM
Replies: 25
Views: 1,220
Posted By Yoyodyne
Re: Stuck block two questions

Amazon etc., it's easy to find and cheap. I use Tasc, product #001 here - https://greenpowerchemical.com/files/116316/PriceList.pdf Much more expensive, I don't know that it's really any better...
Forum: Early V8 (1932-53) 11-05-2020, 03:00 PM
Replies: 25
Views: 1,220
Posted By Yoyodyne
Re: Stuck block two questions

I found the photo. I mixed some in the trash can with hot water from the water heater to try it out. Was a small heater, I ran out of hot water pretty quickly so it wasn't real hot. Dropped this pan...
Forum: Early V8 (1932-53) 11-05-2020, 09:20 AM
Replies: 25
Views: 1,220
Posted By Yoyodyne
Re: Stuck block two questions

Probably Washing Soda - Sodium Carbonate. I do the same, but I don't boil it, I use a bucket heater from tractor Supply. I think I've posted a photo here of how well it works. Cleans that old black...
Forum: Early V8 (1932-53) 11-03-2020, 10:50 PM
Replies: 25
Views: 1,220
Posted By Yoyodyne
Re: Stuck block two questions

Rods are cheap, last one I had to do I torched a few of the rods so I could get the crank out and concentrate on saving the block. I'll sell you a set of 221 rods for $50 if you need them.
Forum: Early V8 (1932-53) 11-01-2020, 07:55 PM
Replies: 27
Views: 1,506
Posted By Yoyodyne
Re: 21 Stud 37mod

Here's my thread about finding a crack in a 37 block in a dumb place after the block was magnafluxed and cleaned and declared good. Not fatal in this case but still would have been a pain if found...
Forum: Early V8 (1932-53) 10-25-2020, 12:17 AM
Replies: 18
Views: 738
Posted By Yoyodyne
Re: L-100 cam in a 221

Most of the new parts sellers have them, they are currently made. I have a set I don't need now.





I had Dave Generous grind my L-100. The only usable core I had at the time was worn...
Forum: Early V8 (1932-53) 10-24-2020, 07:10 PM
Replies: 18
Views: 738
Posted By Yoyodyne
Re: L-100 cam in a 221

Since Pete is here, what is the acceptable smallest diameter for cam journals to reuse? I checked the 3 I have, they range between 1.7955/1.797.


What do (or should) installed cam bearings...
Forum: Early V8 (1932-53) 10-23-2020, 07:55 PM
Replies: 18
Views: 738
Posted By Yoyodyne
Re: L-100 cam in a 221

Thanks for the knowledgeable recommendations! A quick search shows isky cams only for 42-up, would I have to give up the 3 bolt distributor and front plate?
Forum: Early V8 (1932-53) 10-23-2020, 06:26 PM
Replies: 18
Views: 738
Posted By Yoyodyne
L-100 cam in a 221

I've been forced to rethink the motor I've been building and will start over with a 36LB block with maybe .030 overbore and stock stroke. I'll be using stock 36 aluminum heads. I plan to optimize the...
Forum: Early V8 (1932-53) 09-30-2020, 09:58 AM
Replies: 36
Views: 1,254
Posted By Yoyodyne
Re: Oversize OD main bearings for 37 21 stud block

I found 2 pairs of -.030 +.015 inserts for the front and center mains at Red's Vintage auto parts, thanks to Red Hamilton and Marilyn. I'm running out of folks to ask, the few who understand what I'm...
Forum: Early V8 (1932-53) 09-10-2020, 12:36 PM
Replies: 36
Views: 1,254
Posted By Yoyodyne
Re: Oversize OD main bearings for 37 21 stud block

Not so far, that's why started this thread. I'm still hoping to find them, other wise I'm starting over with another block or modifying this one. If I have to modify it, I may as well make it...
Forum: Early V8 (1932-53) 09-10-2020, 10:37 AM
Replies: 36
Views: 1,254
Posted By Yoyodyne
Re: Oversize OD main bearings for 37 21 stud block

L-head - at .015 over you'd have to move the bore centers way too far up into the block to be useful afterward.


Brian, how much narrower are the later center mains? Milling that to size seems...
Forum: Early V8 (1932-53) 09-09-2020, 12:37 AM
Replies: 36
Views: 1,254
Posted By Yoyodyne
Re: Oversize OD main bearings for 37 21 stud block

+1 I was just looking at that this evening, there appears to be room for the larger diameter between the studs. Has anyone done this?
Forum: Early V8 (1932-53) 09-05-2020, 08:18 PM
Replies: 36
Views: 1,254
Posted By Yoyodyne
Re: Oversize OD main bearings for 37 21 stud block

Thanks very much for that Brian. Looks like neither length is correct here. The length issues I can deal with, we have ways to machine it and I can even handscrape if necessary. Putting material on...
Forum: Early V8 (1932-53) 09-05-2020, 07:18 PM
Replies: 36
Views: 1,254
Posted By Yoyodyne
Re: Oversize OD main bearings for 37 21 stud block

The block is 2.083" I have a rear cap from a junk block that measures 2.090" Is the 2.090 standard?
Forum: Early V8 (1932-53) 09-05-2020, 04:47 PM
Replies: 36
Views: 1,254
Posted By Yoyodyne
Re: Oversize OD main bearings for 37 21 stud block

I see. He wasn't specific, just said Ford didn't make them. I asked for other sizes, got no answer so I took that as no rear bearings of any size made.
Forum: Early V8 (1932-53) 09-05-2020, 02:27 PM
Replies: 36
Views: 1,254
Posted By Yoyodyne
Forum: Early V8 (1932-53) 09-05-2020, 02:27 PM
Replies: 36
Views: 1,254
Posted By Yoyodyne
Re: Oversize OD main bearings for 37 21 stud block

I asked him, he doesn't have them. That's who told me there were no rear mains made for this.
Showing results 1 to 25 of 384

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:29 PM.