Forum: Early V8 (1932-53)
03-08-2024, 12:06 PM
|
Replies: 2
Views: 232
Re: 47 pickup front springs
I don't think their is a Spring Shop near me, but I an not few from Easton Pa. I found Hemstreet Auto Spring C0. 5 Haymont St. Easton .
Thanks!
|
Forum: Early V8 (1932-53)
03-07-2024, 04:38 PM
|
Replies: 2
Views: 232
|
Forum: Early V8 (1932-53)
02-06-2024, 03:06 PM
|
Replies: 1
Views: 249
|
Forum: Model A (1928-31)
04-14-2022, 01:28 PM
|
Replies: 1
Views: 644
|
Forum: Model A (1928-31)
12-27-2021, 07:29 AM
|
Replies: 6
Views: 903
|
Forum: Model A (1928-31)
12-26-2021, 02:18 PM
|
Replies: 6
Views: 903
31 Fordor door latch
I need a complete door latch for a 31 Fordor Murray 165C driver side. I have checked with the big suppliers MAC, Snyder's, Gaslight, Midwest Early Ford. with no luck. The one on my car has a lot of...
|
Forum: Model A (1928-31)
01-16-2021, 10:29 AM
|
Replies: 1
Views: 914
Window glass size
Does anyone have correct size for a door glass on a 31 Fordor Murray (165C) rear door?
Ron
|
Forum: Model A (1928-31)
12-30-2020, 03:48 PM
|
Replies: 1
Views: 717
Window glass replacement 31 165C 3 window
need to replace a RR door glass channel part A- 155962-B does anyone have any information on the steps I need to do this job. I also need to replace the channel and have ordered 2 so far and they...
|
Forum: Model A (1928-31)
12-09-2020, 11:52 AM
|
Replies: 4
Views: 1,259
Window glass replacement.
I am replacing the rear right back window on my 31 Fordor murry model. The window seems to move out of the channel when lowered. I installed the window rubber bedding and coated it with a little oil....
|
Forum: Early V8 (1932-53)
09-05-2019, 05:06 PM
|
Replies: 3
Views: 1,286
Electronic distributor 47 pickup
I looked back into old posts but haven't seen anything resent on this subject. I am thinking about covering to a
electronic distributor it seems harder to find original compasitors and I am...
|
Forum: Model A (1928-31)
08-18-2013, 01:30 PM
|
Replies: 22
Views: 4,536
|
Forum: Model A (1928-31)
02-25-2012, 07:26 AM
|
Replies: 6
Views: 1,435
Re: Zephyrhills swap today
All you guys are right! I found one vender had a carb. for a Model A when I decided to buy it at his asking price he said he was going to keep it for a spare and took it off the table. I walked...
|
Forum: Early V8 (1932-53)
11-23-2011, 10:51 AM
|
Replies: 0
Views: 1,110
Body informatioon needed.
I am looking for a book that would show all the body metal and fasters for a 47 ½ ton pickup. Has anyone seen a book or is there a reprint available?
|
Forum: Early V8 (1932-53)
11-22-2011, 07:07 AM
|
Replies: 2
Views: 840
|
Forum: Model A (1928-31)
09-16-2011, 08:02 PM
|
Replies: 33
Views: 8,440
|
Forum: Model A (1928-31)
09-16-2011, 07:52 PM
|
Replies: 23
Views: 4,573
|
Forum: Early V8 (1932-53)
09-11-2011, 08:58 PM
|
Replies: 3
Views: 1,129
Need to replace floor.
Need to replace floor pan on 47 1/2 ton pickup. Looking for a good supplier of metel pans. Anyone who has done this let me know your feed back on this project thanks.
|
Forum: Model A (1928-31)
09-11-2011, 07:18 AM
|
Replies: 1
Views: 1,362
Engine break-in on Model A day
I was able to start my rebuilt engine I got back from the shop. Also was the week for ownering the car 34 years 105,250 miles on the speedometer. Keep them running!
|
Forum: Model A (1928-31)
09-11-2011, 07:05 AM
|
Replies: 3
Views: 1,589
|
Forum: Model A (1928-31)
09-11-2011, 07:02 AM
|
Replies: 12
Views: 2,209
|
Forum: Model A (1928-31)
09-04-2011, 03:53 PM
|
Replies: 14
Views: 2,336
Model A day..
I think I read some where that September 10 is "Model A Day" and anyone with a Model A should take the car out for a run. :)
Ron
|
Forum: Model A (1928-31)
07-08-2011, 07:33 PM
|
Replies: 6
Views: 1,312
|
Forum: Model A (1928-31)
07-07-2011, 04:22 PM
|
Replies: 6
Views: 1,312
Cross member assy.
I am need of a cross member I believe has a part No. A 5020-B for a 31 fourdor standard. The cross member has two square raised mounts for the radiator pads to mount radiator. Could someone lead be...
|
Forum: Model A (1928-31)
06-03-2011, 06:38 AM
|
Replies: 14
Views: 3,117
Need to change engine.
I need to replace engine in my 31 what is the best way buy a rebuilt out right or exchange? Or have my old one replaced? I just looking for some comments or thoughts from members who have been in my...
|
Forum: Model A (1928-31)
05-23-2011, 03:19 PM
|
Replies: 0
Views: 974
The New 2011 Judging Standards.
I received my copy of the updated Judging Standards and after updating my book I notice the Index was not updated. I called the committee chairperson and he said he would look into that. I just...
|