Forum: Model A (1928-31)
09-22-2020, 12:34 PM
|
Replies: 17
Views: 2,263
|
Forum: Model A (1928-31)
08-11-2020, 11:47 AM
|
Replies: 27
Views: 2,986
Re: Hood hinges - tube or rod?
Tubes are stronger Learned this working on hydraulic rods and tubes ,more surface area to bend makes it stronger with less weight.
|
Forum: Model A (1928-31)
06-13-2020, 10:09 PM
|
Replies: 8
Views: 1,492
Re: 31 model A rear end question
Yes, upper is to fill and check , lower to drain. Only fill till when you put your little finger in to your first joint on it. That is all that is needed. Check level a few days later after driving .
|
Forum: Model A (1928-31)
01-21-2020, 05:29 AM
|
Replies: 10
Views: 2,141
|
Forum: Model A (1928-31)
01-19-2020, 02:37 PM
|
Replies: 29
Views: 5,466
|
Forum: Model A (1928-31)
01-19-2020, 02:35 PM
|
Replies: 22
Views: 3,503
|
Forum: Model A (1928-31)
01-09-2020, 10:14 PM
|
Replies: 10
Views: 3,312
|
Forum: Model A (1928-31)
12-10-2019, 10:59 AM
|
Replies: 5
Views: 1,469
Re: 1+ton heavy duty truck wire wheels.
Split ring or split rim . Split rim are dangerous ,do not use . Split ring are also dangerous but if done properly are not as bad . Know how to work on either type or take to truck tire place were...
|
Forum: Model A (1928-31)
11-04-2019, 05:25 PM
|
Replies: 6
Views: 1,709
Re: Temporary Sealant/Caulk
There was a caulk called peelable caulk that I remember from years ago, don't know if still sold for windows . Jim
|
Forum: Model A (1928-31)
10-26-2019, 07:07 PM
|
Replies: 2
Views: 1,048
Re: aa inter tube question
Split rims are dangerous , split ring not so much if you get ring seated in groove wrap tire and rim with a chain around them not real tight .Put air in without needle in stem to lock ring in place...
|
Forum: Model A (1928-31)
10-17-2019, 06:44 PM
|
Replies: 13
Views: 7,238
Re: Model AA High Speed Rear Axel
The 29 should be a worm gear rear end and the 31 should be a ring and pinion set up. The 29 might be a fast rear end than the 31.Jim
|
Forum: Model A (1928-31)
10-13-2019, 12:07 PM
|
Replies: 20
Views: 3,512
Re: Spindle Arm Nut
I think we need a picture so everyone knows what part he is talking aboo9ut.
|
Forum: Model A (1928-31)
10-11-2019, 10:21 AM
|
Replies: 1
Views: 944
|
Forum: Model A (1928-31)
09-24-2019, 08:17 PM
|
Replies: 15
Views: 4,536
|
Forum: Model A (1928-31)
09-24-2019, 08:16 PM
|
Replies: 15
Views: 4,536
|
Forum: Model A (1928-31)
08-13-2019, 11:35 AM
|
Replies: 21
Views: 4,796
|
Forum: Model A (1928-31)
08-13-2019, 11:32 AM
|
Replies: 24
Views: 5,025
Re: Wheel painting
do not let rust get underneath or you will end up with junk wheels , paint is easier to touch up.
|
Forum: Model A (1928-31)
08-13-2019, 11:29 AM
|
Replies: 12
Views: 3,340
|
Forum: Model A (1928-31)
07-29-2019, 08:55 AM
|
Replies: 13
Views: 2,560
Re: Hot 4 Banger radiator question
Go for Berg's , if runs to cool put thermostat in it . Vintage Precision is a nice way to go . You can then put temp probe in below thermostat and see temp.
|
Forum: Model A (1928-31)
06-13-2019, 03:36 PM
|
Replies: 24
Views: 7,358
|
Forum: Model A (1928-31)
04-20-2019, 06:06 AM
|
Replies: 33
Views: 5,362
|
Forum: Model A (1928-31)
03-24-2019, 03:18 PM
|
Replies: 5
Views: 1,442
Re: Preparing a 1931 Instrument panel for plating
You need to strip off all plating to repair underlying metal . Use very fine sand paper to make a mirror finish. What you see in metal before plating is what comes thru as your finish. Truckerjim
|