Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: 42merc
Forum: Early V8 (1932-53) 07-05-2021, 06:06 PM
Replies: 5
Views: 328
Posted By 42merc
Re: 39 coupe curling rear window seal

Your existing seals are probably Carpenter brand seals. As built they are too long & curl after installation.
Buy Drake seals, they will fit correctly.
Forum: Early V8 (1932-53) 06-19-2021, 12:07 PM
Replies: 9
Views: 683
Posted By 42merc
Re: Shocked by the Horn!!!!

The horn button ground "path" is not clean. Your body is completing the ground circuit.
Maybe add a ground wire from the column to the frame.
Also clean the steering wheel under the horn button.
Forum: Early V8 (1932-53) 06-17-2021, 11:17 AM
Replies: 8
Views: 635
Posted By 42merc
Re: 1935 Experimental intake

Take notice that Sheldon lives in France.
Forum: Early V8 (1932-53) 05-22-2021, 06:07 PM
Replies: 10
Views: 545
Posted By 42merc
Re: 40 Standard Grille Repair

Real '40 Ford standard grilles are die cast.
Once upon a time the aftermarket produced a stamped steel grille.
Forum: Early V8 (1932-53) 05-14-2021, 07:01 AM
Replies: 36
Views: 1,781
Posted By 42merc
Re: Flathead Oil Pan

It's a 1953 F100 truck V8 flathead oil pan. One year only.
Forum: Early V8 (1932-53) 03-20-2021, 05:33 PM
Replies: 2
Views: 352
Posted By 42merc
Re: 40 hubs

They will fit '45-'47, not '48.
'48 gets you the "new" F1 & Bendix brakes.
Forum: Early V8 (1932-53) 03-01-2021, 05:18 PM
Replies: 32
Views: 2,335
Posted By 42merc
Re: Transmission Oil

If you put GL5 in a gearbox with yellow metals it will discolor the yellow metals after several years. It will NOT dissolve them in a few minutes like most people believe.

This I agree with.
Forum: Early V8 (1932-53) 02-21-2021, 08:49 PM
Replies: 13
Views: 783
Posted By 42merc
Re: Crank pulley

Crank snout on the 37 is a smaller diameter than the 46-48 crank.
Forum: Early V8 (1932-53) 02-19-2021, 03:22 PM
Replies: 23
Views: 2,223
Posted By 42merc
Re: Flathead identification

After looking a bit harder, I think we have an EAB long block with the truck stuff bolted on, (bell housing, exhaust, water pumps, generator, fan & early oil filter). Plus there is an oil filter lug...
Forum: Early V8 (1932-53) 02-17-2021, 06:14 PM
Replies: 23
Views: 2,223
Posted By 42merc
Re: Flathead identification

The 1948 early 1949 version of the 8ba/8rt used the early (42-48) wide bolt pattern oil filter.
Forum: Early V8 (1932-53) 02-15-2021, 07:32 PM
Replies: 12
Views: 1,184
Posted By 42merc
Re: Reds headers & Brockman exhaust

The Steelpack Brockman's will be louder at the tailpipe than the other mentioned mufflers.
I have used Brockman glasspacks on several flathead powered cars & I love them, slightly less loud than...
Forum: Early V8 (1932-53) 02-14-2021, 09:09 PM
Replies: 12
Views: 1,128
Posted By 42merc
Forum: Questions & Suggestions 02-06-2021, 04:57 PM
Replies: 3
Views: 864
Posted By 42merc
Re: 324-371 Olds

Yes, it will fit.
Forum: Early V8 (1932-53) 02-05-2021, 05:39 PM
Replies: 62
Views: 6,571
Posted By 42merc
Forum: Early V8 (1932-53) 02-02-2021, 08:55 PM
Replies: 10
Views: 1,196
Posted By 42merc
Re: not a fan.

I posted this in 2017. I've used this method several times.


Everyone has their own solution for this common problem, this is mine. You must have a '40 fan mount pulley to start with. Remove...
Forum: Model A (1928-31) 02-01-2021, 09:28 PM
Replies: 9
Views: 886
Posted By 42merc
Re: Any luck with paint from tcp?

I've used TCP acrylic enamel. Colors were not spot on, but the paint was good to work with.
Forum: Early V8 (1932-53) 01-29-2021, 08:28 PM
Replies: 8
Views: 670
Posted By 42merc
Re: Intake Manifold Weep

Check the heater hose connections.
Forum: Early V8 (1932-53) 01-23-2021, 12:43 PM
Replies: 21
Views: 1,698
Posted By 42merc
Re: Woodie Auction today in Auburn, IN

My '42 maroon Mercury wagon was a regular at the Indy swap meet from mid '80's thru the late '90's.
Still have it, but not driven lately.

The Mercs pictured above came from the Nick Alexander...
Forum: Early V8 (1932-53) 01-21-2021, 07:00 PM
Replies: 8
Views: 919
Posted By 42merc
Re: 1946 Mercury exhaust system source?

The added length of the Mercury is forward of the cowel.
The motor and drive train is is in the same location as a Ford. The difference happens with the steering gear, about 4 inches more forward...
Forum: Early V8 (1932-53) 01-07-2021, 06:11 PM
Replies: 2
Views: 345
Posted By 42merc
Re: 1940 rear hub material

The hubs are forged steel.
Forum: Early V8 (1932-53) 10-22-2020, 08:26 PM
Replies: 18
Views: 1,264
Posted By 42merc
Re: 1940 merc & ford x member replace

When it comes to Hot Rods, A Ford in a Ford is not traditional, unless it's a flathead.
Forum: Early V8 (1932-53) 10-21-2020, 06:56 AM
Replies: 18
Views: 1,264
Posted By 42merc
Re: 1940 merc & ford x member replace

Check out Pete & Jake's.
They sell a kit developed by "Mor-Fab" , looks good to me.
Forum: Early V8 (1932-53) 10-16-2020, 04:35 PM
Replies: 14
Views: 4,220
Posted By 42merc
Forum: Early V8 (1932-53) 10-14-2020, 12:55 PM
Replies: 8
Views: 503
Posted By 42merc
Forum: Early V8 (1932-53) 09-28-2020, 08:35 AM
Replies: 10
Views: 1,398
Posted By 42merc
Re: pre-war bumper jack ID

The Jack was manufactured by Auto Specialties Mfg. "AUSCO", .Saint Joseph, Michigan.
The company made many products for the auto industry. They have been out of business for several years. The wagon...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:12 AM.