Forum: Early V8 (1932-53)
07-16-2020, 09:41 AM
|
Replies: 17
Views: 2,566
Re: '35 Coupe 5 window value
I would ask what the person is wanting and since it doesn't run thats you bargaining tool and since it needs interior thats about 4,000 plus dollars right their so if the engine is not seized up...
|
Forum: Early V8 (1932-53)
07-16-2020, 09:22 AM
|
Replies: 23
Views: 4,275
|
Forum: Early V8 (1932-53)
07-16-2020, 09:16 AM
|
Replies: 23
Views: 4,275
Re: 1935/36 roof tack strip
Mac sells a tack strip for the door jamb B pillar and it might work. It's made of a hard rubber material and comes in two sizes and you tell them how long it needs to be and it's sold by the foot...
|
Forum: Early V8 (1932-53)
09-02-2014, 02:19 PM
|
Replies: 42
Views: 26,394
|
Forum: Early V8 (1932-53)
09-02-2014, 02:10 PM
|
Replies: 42
Views: 26,394
Re: 6 volt relays
Low voltage will cause it to heat up and burn out sooner if it works at all
|
Forum: Early V8 (1932-53)
09-02-2014, 02:06 PM
|
Replies: 42
Views: 26,394
Re: 6 volt relays
Speedway Motors has them for fans and such for hot rods their 6 volt and good for 20/30 amps and their made by Bosch. They have a terminal for a normanly open circut and one or a normanly closed...
|
Forum: Early V8
01-16-2014, 08:31 AM
|
Replies: 3
Views: 2,133
|
Forum: Early V8
12-31-2013, 05:37 PM
|
Replies: 9
Views: 2,513
Re: 1935 Ford rear hubs and drums
How good are the tapers and keyways where the axle goes, Ive seen many a hub that looks good on the outside but the taper are all worne out fron the key way chewing the taper out real bad ? Thanks...
|
Forum: Early V8
12-31-2013, 05:34 PM
|
Replies: 9
Views: 2,513
Re: 1935 Ford rear hubs and drums
How good are the tapers and keyways where the axle goes, Ive seen many a hub that looks good on the outside but the taper are all worne out fron the key way chewing the taper out real bad ? Thanks...
|
Forum: Early V8 (1932-53)
12-23-2013, 05:15 PM
|
Replies: 7
Views: 2,260
Re: 1935 Fordor B-Pillar
The pillars are replaceable but not easly because you need to jig the body before removal and install otherwise the doors wont line up correctally and welding is required at the top and rivets on the...
|
Forum: Early V8 (1932-53)
04-03-2013, 05:44 PM
|
Replies: 15
Views: 2,842
Re: Air Scoop screen wire filter for 35-36 Fords
If you use the scoop style air breather use a paper filter and a screen to keep it looking original and the dirt problem wont be a problem, and I use an oil filter from a Toyota cut it apart and...
|
Forum: Early V8 (1932-53)
04-02-2013, 11:51 AM
|
Replies: 40
Views: 14,353
|
Forum: Early V8 (1932-53)
03-06-2013, 11:33 AM
|
Replies: 15
Views: 2,842
|
Forum: Early V8 (1932-53)
03-04-2013, 02:20 PM
|
Replies: 12
Views: 5,880
Re: 1936 ford fuel gauge hook up?
top is hot bottom is sending unit wire do not use 12 volts or you'll smoke the gauge , use a runt or something compatible that will handle the resistance full time to drop the voltage down to 6...
|
Forum: Early V8 (1932-53)
03-02-2013, 03:13 PM
|
Replies: 14
Views: 7,528
Re: Oil Pressure Sending Unit Question
The sending units are matched to the gauge so the 35-36 gauges need the 50# sending unit and the later cars where the pressure was higher need the 80# sending unit as well as the proper gauge to...
|
Forum: Early V8 (1932-53)
02-15-2013, 03:09 PM
|
Replies: 100
Views: 19,797
Re: Which do you prefer 1935 or 1936??
5 window 35 because I have one and like the grill and wire wheels and horns . But if I could have both I wouldnt complain at all especially a 36 roadster or a 35 roadster.
|
Forum: Early V8
11-01-2012, 06:33 PM
|
Replies: 5
Views: 2,871
Re: 1935 ford 3 window frame and parts
To take a 35 3 window like that and rod it is not a GOOD IDEA , iT'S WORTH WAY MORE STOCK TO SOMEONE WHO WANTS IT ALL ORIGINAL AND PROBABLY WOULD BE WORTH ABOUT 45,000.00 IF THE PIC IS A GOOD...
|
Forum: Early V8
10-17-2012, 07:01 PM
|
Replies: 13
Views: 2,504
|
Forum: Early V8
10-17-2012, 05:13 PM
|
Replies: 9
Views: 8,553
|
Forum: Early V8
10-17-2012, 05:10 PM
|
Replies: 1
Views: 1,226
|