Forum: Early V8 (1932-53)
02-27-2021, 06:52 PM
|
Replies: 1
Views: 229
Early intake manifold
Found a intake manifold the other day that the fuel pump mounted directly to the manifold ,,what year would this be?
|
Forum: Early V8 (1932-53)
02-24-2021, 07:10 PM
|
Replies: 190
Views: 6,991
|
Forum: Early V8 (1932-53)
12-30-2020, 08:02 AM
|
Replies: 67
Views: 2,102
Re: Misery loves company
Ever take something apart that had 6 screws,go to put it all back togeather and only have 5 screws,!!!
|
Forum: Early V8 (1932-53)
11-16-2020, 04:23 PM
|
Replies: 22
Views: 1,293
|
Forum: Early V8 (1932-53)
11-11-2020, 06:12 PM
|
Replies: 18
Views: 507
|
Forum: Model-A
10-30-2020, 09:33 AM
|
Replies: 0
Views: 291
29 roadster pick up
446067
Very nice pick up,completely rebuilt from nice wester vehicle,would go high in a points judging show,,
Pdonjan@aol.com
|
Forum: Early V8
10-26-2020, 08:06 PM
|
Replies: 0
Views: 182
|
Forum: Model-A
10-26-2020, 01:17 PM
|
Replies: 0
Views: 271
29 roadster pick up for sale
445708
445709
445710
Excellent little pick up for show or go! Needs nothing, rebuilt from ground up from western car,
1-606-325-3538
Pdonjan@aol.com
$22k
|
Forum: Early V8 (1932-53)
10-16-2020, 01:50 PM
|
Replies: 16
Views: 949
|
Forum: Early V8 (1932-53)
09-30-2020, 02:53 PM
|
Replies: 20
Views: 979
|
Forum: Early V8 (1932-53)
09-25-2020, 04:36 PM
|
Replies: 55
Views: 3,147
|
Forum: Early V8 (1932-53)
09-22-2020, 05:24 PM
|
Replies: 10
Views: 651
|
Forum: Early V8 (1932-53)
09-21-2020, 02:15 PM
|
Replies: 12
Views: 738
Re: Engine stops when it is hot
I think people should check the current draw of ignition circuit more often when a coil is suspect or getting hot, or the resistance in circuit is in question,I think about 3 amps give or take a...
|
Forum: Early V8 (1932-53)
09-16-2020, 09:32 PM
|
Replies: 12
Views: 829
Re: Low comp on one. Yl
Got engine all back and running after freeing rings in number 7 ,,new piston,,after running a short time started missing !,changed carb same thing,changed dist and cond, same thing,pulled plug wire...
|
Forum: Early V8 (1932-53)
09-15-2020, 06:13 AM
|
Replies: 13
Views: 855
Re: Optima battery will only chug to 50%
Thanks for info Paul,think I’ll parallel a 6 volt optima with the bad one and try charging to see if that works,if not might go for the charger you mention,sure cheaper that a new battery at $185,,
|
Forum: Early V8 (1932-53)
09-12-2020, 12:41 PM
|
Replies: 13
Views: 855
Re: Optima battery will only chug to 50%
Battery charger is a scheaur(spelling) that has a percentage meter also has settings for agm settings,
I also have optimum batteries in my roadster and model A ,at least 10 years on both and very...
|
Forum: Early V8 (1932-53)
09-12-2020, 09:06 AM
|
Replies: 13
Views: 855
Optima battery will only chug to 50%
Optima red top 6 volt will only charge to a little over 50% ,then charger shuts down,l just use it in shop for engine stand,trickle charge it when I think about it,,never leave it more than a...
|
Forum: Early V8 (1932-53)
08-27-2020, 05:02 PM
|
Replies: 12
Views: 829
Re: Low comp on one. Yl
Got piston out a few minutes,second and third ring were stuck in grove,,these are four ring pistons ..top ring was loose ,,,
I was very careful when installing rings. so sure there on correct,
I...
|
Forum: Early V8 (1932-53)
08-27-2020, 06:28 AM
|
Replies: 12
Views: 829
|
Forum: Early V8 (1932-53)
08-26-2020, 08:03 PM
|
Replies: 12
Views: 829
|
Forum: Early V8 (1932-53)
08-26-2020, 03:18 PM
|
Replies: 12
Views: 829
Low comp on one. Yl
After rebuilding a 21 stud,doing a valve job !new rings and everything else,,put on engine stand,bad miss!rechecked everything!dist ,wires took off intake ,recheck valve clearance,everything good but...
|
Forum: Early V8 (1932-53)
08-25-2020, 05:33 AM
|
Replies: 6
Views: 505
Re: Steel head gaskets
Coctacted fel pro tech line! Also ,,,guy said copper coat or there was another sealer I forgot,!,,
|
Forum: Early V8 (1932-53)
08-24-2020, 12:51 PM
|
Replies: 6
Views: 505
Steel head gaskets
What do I put on a 21 stud steel head gasket with cast iron heads to get a good seal?? Copper coat,grease,or silver paint or nothing
I used copper coat on a composit gasket the other day,had a stuck...
|
Forum: Early V8 (1932-53)
08-19-2020, 06:37 PM
|
Replies: 5
Views: 470
Re: Master cylinder fill cap
I took cap from old MC or even new one and drilled a tap for 1/4 pipe,then used a compression fitting to apply air and fluid,,when done ,just removed the comp fitting and put a 1/4 pipe plug in BE...
|
Forum: Early V8 (1932-53)
08-18-2020, 08:14 PM
|
Replies: 12
Views: 680
Re: Brake pedal clearance desapears
Shortened the MC rod and that fixed the full pedal problem,good hard pedal and down to normal position,,,always good to get a second opinion!!! Tks,,
|