Forum: Model A (1928-31)
06-09-2018, 04:22 PM
|
Replies: 6
Views: 1,795
Re: Babbiting
It's not exactly Ohio, but I recommend Dennis Piranio of Piranio Antique Automotive in Denton, Texas. Excellent babbit and machine work. If you are planning on a touring engine, I suggest you talk...
|
Forum: Model A (1928-31)
06-08-2018, 09:02 PM
|
Replies: 8
Views: 1,526
|
Forum: Model A (1928-31)
06-08-2018, 04:47 PM
|
Replies: 8
Views: 1,526
|
Forum: Model A (1928-31)
06-08-2018, 03:46 PM
|
Replies: 8
Views: 1,526
Re: Starter Issue
Anybody ever have this problem where the starter motor keeps running after the engine starts?
|
Forum: Model A (1928-31)
06-08-2018, 11:50 AM
|
Replies: 8
Views: 1,526
Starter Issue
On several occasions my starter has kept turning after the engine starts and bendix releases. What could be causing this? I'm still on the original 6 volt system.
|
Forum: Model A (1928-31)
11-30-2017, 08:00 PM
|
Replies: 7
Views: 1,801
Re: Steering Wheel Install - What did I do wrong?
Thanks for the replies. I'm pretty sure I installed the bushing but I will double check. The horn rod is the orignal rod so there should not be any fitment issues. I may have found the culprit. ...
|
Forum: Model A (1928-31)
11-30-2017, 02:35 PM
|
Replies: 7
Views: 1,801
|
Forum: Model A (1928-31)
07-22-2017, 10:04 PM
|
Replies: 27
Views: 14,156
Re: Elkpointe & Kawanee Green Paint
Here is my version. Used the color chips in the paint manual to get as close as I could working with the folks at the local English Color store. And then, at the end of the day, I went with what I...
|
Forum: Model A (1928-31)
07-14-2017, 08:52 PM
|
Replies: 14
Views: 2,485
|
Forum: Model A (1928-31)
07-14-2017, 06:14 PM
|
Replies: 5
Views: 1,440
Re: Timing gear Recess
Is there a way to find TDC without removing the head, since the spark plug is offset from the piston?
|
Forum: Model A (1928-31)
07-14-2017, 05:13 PM
|
Replies: 5
Views: 1,440
Timing gear Recess
The recess/indention in the timing gear that is used when setting the timing on my car is very shallow and I have a hard time finding TDC for #1 cylinder. This is a new fiber gear that I installed...
|
Forum: Model A (1928-31)
07-09-2017, 03:07 PM
|
Replies: 21
Views: 3,394
|
Forum: Model A (1928-31)
07-09-2017, 09:39 AM
|
Replies: 21
Views: 3,394
Stop Light Location
Where can I find dimensional data on the location of the stop light bracket on the rear fenders (I'm putting stop lights on both fenders)? I didn't have enough sense to measure the bolt holes on the...
|
Forum: Model A (1928-31)
07-08-2017, 06:40 PM
|
Replies: 19
Views: 3,568
|
Forum: Model A (1928-31)
07-08-2017, 03:32 PM
|
Replies: 19
Views: 3,568
|
Forum: Model A (1928-31)
07-08-2017, 03:03 PM
|
Replies: 19
Views: 3,568
Exhaust leak secrets
What's the trick to stopping a small leak between the exhaust manifold and muffler? I bought a new clamp, seal, and exhaust sleeve. made sure there was a good fit between the muffler and manifold...
|
Forum: Model A (1928-31)
07-01-2017, 05:10 PM
|
Replies: 9
Views: 2,745
|
Forum: Model A (1928-31)
07-01-2017, 03:48 PM
|
Replies: 9
Views: 2,745
Spare Tire Carrier - Is there a gasket?
For the spare tire carriers that fit on the trunk of the Std Coupe (w/rumble seat), is there a rubber gasket, etc that fits between the carrier and the trunk?
|
Forum: Model A (1928-31)
06-26-2017, 04:30 PM
|
Replies: 9
Views: 1,429
Re: Windshield - what goes here??
Thanks Jason. That flat piece is what I didn't see looking into the hole. I have ordered a screw kit which includes the nuts. Thanks.
|
Forum: Model A (1928-31)
06-26-2017, 02:59 PM
|
Replies: 9
Views: 1,429
Re: Windshield - what goes here??
Jason,
Thanks for the response. I have the piece you are talking about and the screws fit into the side of the frame as you state. But mine also has two holes at the top (one each side) as shown...
|
Forum: Model A (1928-31)
06-26-2017, 02:32 PM
|
Replies: 9
Views: 1,429
Windshield - what goes here??
What type of screw goes into the two holes at the top of the windshield frame and what do they screw into? The hole extends into the channel that holds the rubber seals. Is this intended to hold...
|
Forum: Model A (1928-31)
04-19-2017, 05:40 PM
|
Replies: 4
Views: 1,251
Re: roof/visor fit
jdupay, you are right that the metal trim piece is missing, as well as the front header wood. I took that off to see if I needed to shape the wood some to make the top metal fit better. But it it...
|
Forum: Model A (1928-31)
04-19-2017, 02:52 PM
|
Replies: 4
Views: 1,251
roof/visor fit
Putting the car back together I have run into an issue where the roof meets with the visor. Is it normal to have the amount of gap shown in the pictures? I don't see how the trim piece would ever...
|
Forum: Model A (1928-31)
03-30-2017, 08:06 PM
|
Replies: 13
Views: 2,190
|
Forum: Model A (1928-31)
03-30-2017, 09:53 AM
|
Replies: 13
Views: 2,190
Re: Rear Hub Tightening
Thanks for all the excellent input. Looks like I need to size the brake shoes to the new drum. My assumption was that since I was not replacing the shoes they were worn enough and would be OK. BAD...
|