Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.07 seconds.
Search: Posts Made By: katy
Forum: Model A (1928-31) Yesterday, 08:02 PM
Replies: 4
Views: 186
Posted By katy
Re: Question about 1930 Tudor dovetails

Thanks, I didn't realize that they were called dovetails.
Forum: Model A (1928-31) Yesterday, 12:38 PM
Replies: 12
Views: 449
Posted By katy
Re: Torque wrench

Get new grade 8 bolts and nuts and start over.
Forum: Model A (1928-31) Yesterday, 12:34 PM
Replies: 14
Views: 1,170
Posted By katy
Re: Snap-On Dwell Tach

Looks self explanatory to me. Decide which RPM range desired, then select 4,6 or 8 cylinder engine. Bob's your uncle.
Forum: Model A (1928-31) Yesterday, 12:28 PM
Replies: 6
Views: 239
Posted By katy
Re: Horn electrical terminal connection

The clip on the right looks OK but the one on the left looks gimballed up
Forum: Model A (1928-31) Yesterday, 12:18 PM
Replies: 4
Views: 186
Posted By katy
Re: Question about 1930 Tudor dovetails

Please explain the dovetail.
Forum: Model A (1928-31) Yesterday, 11:59 AM
Replies: 38
Views: 2,184
Posted By katy
Re: Wheel Washers

Cast iron drum is a lot thicker than a steel one.
Forum: Model A (1928-31) Yesterday, 11:46 AM
Replies: 46
Views: 1,687
Posted By katy
Forum: Model A (1928-31) 09-24-2021, 10:38 AM
Replies: 15
Views: 645
Posted By katy
Re: Champion 3x electrode

Just set the gap at .035", put them back in and go.
Forum: Model A (1928-31) 09-23-2021, 10:59 AM
Replies: 21
Views: 1,323
Posted By katy
Re: Vacuum Gauge (new)

It's worth a try, start small.
Forum: Model A (1928-31) 09-23-2021, 10:39 AM
Replies: 17
Views: 959
Posted By katy
Re: Rebuilding my generator...

Check if the points are closed or open before turning the key on, if the points are closed the ammeter will show a draw, if the points are open there should be no draw.
Forum: Model A (1928-31) 09-23-2021, 10:29 AM
Replies: 38
Views: 2,184
Posted By katy
Re: Wheel Washers

Be sure and check the axle nut torque after the first few miles and then again and again, to ensure that it stays tight.
I hope you made sure the axle, the shims, and the hub (where the axle fits)...
Forum: Model A (1928-31) 09-22-2021, 10:35 AM
Replies: 8
Views: 407
Posted By katy
Re: Rear Drum Seal

A picture would definitely help.
Forum: Model A (1928-31) 09-22-2021, 10:28 AM
Replies: 9
Views: 462
Posted By katy
Re: Help Identifying Part Please

The rubber made for shower doors might be an option.
Forum: Model A (1928-31) 09-21-2021, 11:21 AM
Replies: 40
Views: 2,966
Posted By katy
Re: Clear Distributor Cap

I'm wondering, why the tie wire on the distributor body terminals?
Forum: Model A (1928-31) 09-21-2021, 10:27 AM
Replies: 46
Views: 1,687
Posted By katy
Re: Overheating 1930 Model A

If one uses dishwasher detergent to clean the cooling system be sure and get the low sudsing type. Don't ask.
Forum: Model A (1928-31) 09-20-2021, 12:07 PM
Replies: 10
Views: 710
Posted By katy
Re: So, I have apparently blown head gasket

Be sure and use the low sudsing type of detergent.
Forum: Model A (1928-31) 09-20-2021, 11:45 AM
Replies: 46
Views: 1,687
Posted By katy
Re: Overheating 1930 Model A

That's a good trick.



Ditto
Forum: Model A (1928-31) 09-20-2021, 11:26 AM
Replies: 29
Views: 1,570
Posted By katy
Re: hoky fixs

Here's a chart:
Forum: Model A (1928-31) 09-20-2021, 11:16 AM
Replies: 16
Views: 624
Posted By katy
Re: Squeaking near front crank pulley

I had a similar "hard to find squeek", it was where the front motor mount sits on the crossmember. Squirt a little oil on that, it's worth a try..
Forum: Model A (1928-31) 09-15-2021, 10:35 AM
Replies: 42
Views: 1,349
Posted By katy
Re: A few timing gear questions

The tooth mark on my CCPU engine was on the front.
Forum: Model A (1928-31) 09-15-2021, 10:20 AM
Replies: 18
Views: 693
Posted By katy
Re: '28 Tudor: Wood blocks

True, but I was thinkin' "the sidewalls of an old tire", not a tube.
Forum: Model A (1928-31) 09-15-2021, 10:14 AM
Replies: 34
Views: 1,333
Posted By katy
Re: Four Post Lift Recommendations….

Thanks

Late Model, love your '56
Forum: Model A (1928-31) 09-15-2021, 10:08 AM
Replies: 11
Views: 605
Posted By katy
Re: Gas bowl Q…

Hmmm, I've seen them used for shot glasses.
Forum: Model A (1928-31) 09-14-2021, 11:05 AM
Replies: 112
Views: 5,272
Posted By katy
Re: 1929 double a won't start, help

Goerge Moir in Stony Plain, Alberta or The Old Car Centre in Langley, BC

There should be some suppliers in Eastern Canada
Forum: Model A (1928-31) 09-14-2021, 11:00 AM
Replies: 22
Views: 849
Posted By katy
Re: Voltage/Amperage question?

FSB equates to Ford Service Bulletin
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:07 PM.