Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.12 seconds.
Search: Posts Made By: BRENT in 10-uh-C
Forum: Model A (1928-31) Yesterday, 04:58 PM
Replies: 9
Views: 510
Posted By BRENT in 10-uh-C
Re: Repair of Soft Wood

The product is still around, -just not the re-packaged/re-branded name. The epoxy was a methylmethaccrylate that is used in the repair of horse hooves.
Forum: Model A (1928-31) 11-25-2020, 03:53 PM
Replies: 9
Views: 510
Posted By BRENT in 10-uh-C
Re: Repair of Soft Wood

I will tell you straight-up that you are approaching a path that you will likely regret. Early on in my professional career I used Kwik-Poly on two separate Fordors trying to save my customer money....
Forum: Model A (1928-31) 11-24-2020, 02:25 PM
Replies: 22
Views: 1,022
Posted By BRENT in 10-uh-C
Re: "A" with wooden spoke wheels....

Ray, I think this is a unwarranted 'preconceived thought' that Model-Ts are dangerous with wooden wheels. While I agree that wood can rot, most hickory spokes do not if the vehicle is garage kept...
Forum: Model A (1928-31) 11-24-2020, 08:48 AM
Replies: 6
Views: 533
Posted By BRENT in 10-uh-C
Re: Kick panel with document storage

The DeLuxe open cars used this pocket. Ask your upholstery supplier to add that feature into a set of panels that matches your bodystyle.
Forum: Model A (1928-31) 11-24-2020, 08:46 AM
Replies: 47
Views: 2,451
Posted By BRENT in 10-uh-C
Re: Bone Stock or Modified?

There is a real irony in many hobbyist's perception that often things are done to improve safety and/or reliability. When you stop to study those comments, it should quickly be a realization that...
Forum: Model A (1928-31) 11-24-2020, 08:23 AM
Replies: 17
Views: 670
Posted By BRENT in 10-uh-C
Re: Flywheel housing mounting

Marc, some thoughts based on my experiences. The main reasons why flywheel housings crack is because the rear motor mounts have broken which allowed the engine to flex or move in the frame. IMO,...
Forum: Model A (1928-31) 11-23-2020, 04:51 PM
Replies: 20
Views: 3,435
Posted By BRENT in 10-uh-C
Re: Double Nut Lifters Secrets

George, welcome to Fordbarn.

I think I may have a set at the shop that I can send you a picture of that shows the difference. You must measure your lash at the base of the cam lobe however to...
Forum: Model A (1928-31) 11-23-2020, 03:28 PM
Replies: 35
Views: 1,659
Posted By BRENT in 10-uh-C
Re: Most Difficult Restoration Tasks

Here is one area that I am struggling with this week! :D

Click here: https://www.fordbarn.com/forum/showpost.php?p=1955376&postcount=11
Forum: Model A (1928-31) 11-23-2020, 03:25 PM
Replies: 10
Views: 446
Posted By BRENT in 10-uh-C
Re: 31 Roadster wood floor pattern

This is where a drum sander comes in handy. The ¾" Plywood has a nominal thickness ²³⁄₃₂" which is 0.719", and the ¹¹⁄₁₆" Plywood should have a finish size of around 0.687". That means if we remove...
Forum: Model A (1928-31) 11-22-2020, 06:45 PM
Replies: 10
Views: 446
Posted By BRENT in 10-uh-C
Re: 31 Roadster wood floor pattern

The biggest difference is most commercially available reproduction floorboards are the incorrect thickness.
Forum: Model A (1928-31) 11-22-2020, 06:43 PM
Replies: 47
Views: 2,451
Posted By BRENT in 10-uh-C
Re: Bone Stock or Modified?

I have discussed this very topic on more than just a few occasions. My general feeling is it often deals with the owner's skillset. Many restorers that do Fine-point restorations are not doing it...
Forum: Model A (1928-31) 11-22-2020, 04:17 PM
Replies: 36
Views: 1,694
Posted By BRENT in 10-uh-C
Re: Hard Brake Pedal - Update on Post #9

While you have the front drum off, pay close attention to the brake wedge to see if it is binding on the stud as the brake is depressed. Especially if it has the floater with the pin inside.
Forum: Model A (1928-31) 11-22-2020, 04:12 PM
Replies: 15
Views: 1,480
Posted By BRENT in 10-uh-C
Re: spring perches, castle nuts, and cotter keys

Yes, look at post #3 above. Those were absolute junk. They did not fit the front radius rod correctly and as Roger said above, the holes were not drilled correctly. I think most vendors sent them...
Forum: Model A (1928-31) 11-22-2020, 04:09 PM
Replies: 19
Views: 781
Posted By BRENT in 10-uh-C
Re: Remove sludge from bottom of gas tank

If it is only dried fuel, then anything that will dissolve something organic. Sometime using denatured alcohol or lacquer thinner can soften old residues where they can be flushed out. Gasoline...
Forum: Model A (1928-31) 11-22-2020, 02:16 PM
Replies: 12
Views: 976
Posted By BRENT in 10-uh-C
Forum: Model A (1928-31) 11-22-2020, 02:09 PM
Replies: 24
Views: 971
Posted By BRENT in 10-uh-C
Re: Engine upgrade

From the perspective of an engine rebuilder, it is WAY easier to install a high-compression head at a later date than it is to install larger intake valves. If your budget is tight, opt for a new...
Forum: Model A (1928-31) 11-22-2020, 01:16 PM
Replies: 35
Views: 1,659
Posted By BRENT in 10-uh-C
Re: Most Difficult Restoration Tasks

I will share a little secret from my side of the fence. I got this trick from from my Dad and I have modified it for my business. It is very easy to get overwhelmed, ...and especially if you have...
Forum: Model A (1928-31) 11-20-2020, 01:45 PM
Replies: 35
Views: 1,659
Posted By BRENT in 10-uh-C
Re: Most Difficult Restoration Tasks

Bob, now that you have done it, do you think they would be difficult the second (-or third) time you did that task?? Always remember;

, , , , 'Experience is something you don't get until...
Forum: Model A (1928-31) 11-20-2020, 10:42 AM
Replies: 20
Views: 3,953
Posted By BRENT in 10-uh-C
Re: Kwik way lbm

So you are using an LBM to cut poured bearings in Model-T blocks & caps?
Forum: Model A (1928-31) 11-20-2020, 10:12 AM
Replies: 12
Views: 976
Posted By BRENT in 10-uh-C
Re: Can anyone share any information about the “birth” of this forum.

Actually, Shelley did not start Fordbarn. Fordbarn goes back WAY further than that. This forum was the brainchild of a guy named Gus Stangeland from the Dallas area who started this forum for his...
Forum: Model A (1928-31) 11-19-2020, 11:38 AM
Replies: 20
Views: 3,953
Posted By BRENT in 10-uh-C
Re: Kwik way lbm

I doubt you are going to find any new tooling for your machine. Therefore you will need to make it yourself. Various supply stores such as MSC or McMaster will offer a ⁵⁄₁₆/.3125 HSS blank that you...
Forum: Model A (1928-31) 11-18-2020, 05:02 PM
Replies: 25
Views: 1,721
Posted By BRENT in 10-uh-C
Re: Original Fan Belts...NOS

You purchase both, and then you have $502.50 in each one.
Forum: Model A (1928-31) 11-18-2020, 05:00 PM
Replies: 5
Views: 337
Posted By BRENT in 10-uh-C
Forum: Model A (1928-31) 11-18-2020, 03:38 PM
Replies: 25
Views: 1,721
Posted By BRENT in 10-uh-C
Re: Original Fan Belts...NOS

To begin with, it is quite evident y'all have no idea what you are discussing. To begin with, it is a needed item if you plan to [U]authentically[U] restore your Model-A. Making fun of someone else...
Forum: Model A (1928-31) 11-18-2020, 09:29 AM
Replies: 11
Views: 1,181
Posted By BRENT in 10-uh-C
Re: price on car

Seems like he already has it running. The motor was locked up (i.e.: stuck) but added some oil and it goes real fast now.

I think the rest of your advice is pretty spot-on for this level of car. ...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:11 AM.