Forum: Model A (1928-31)
02-12-2017, 05:04 PM
|
Replies: 5
Views: 3,689
|
Forum: Model A (1928-31)
09-24-2016, 05:40 AM
|
Replies: 2
Views: 1,165
Interior wood kit
28 tudor is about to be given a final painting. Interior work to follow. Is it best to install the new interior wood kit before the paint job or after.
|
Forum: Model A (1928-31)
08-11-2013, 10:37 AM
|
Replies: 10
Views: 3,623
charging 6 volt batteries in series
Recent reviews of recommendations for charging a 6 volt battery with a 12 volt charger emphasize connecting the 6 volt batteries(2) in series then using a 12 volt charger to charge both. Must both...
|
Forum: Model A (1928-31)
07-03-2013, 06:53 PM
|
Replies: 6
Views: 1,652
Re: Startup of 28 tudor - HELP!
Problem appears to have been caused by wires from a new wiring harness, not yet attached to headlights shorting out on the floor. All were caped off , problem gone.
The start up process...
|
Forum: Model A (1928-31)
07-03-2013, 10:27 AM
|
Replies: 6
Views: 1,652
Startup of 28 tudor - HELP!
After 15 years of rebuilding, car is scheduled for a start up. When I made the final hookup of a new battery, to all new wiring, a big spark resulted.
Is equiped with a shutoff switch next to...
|
Forum: Model A (1928-31)
06-19-2013, 07:19 AM
|
Replies: 6
Views: 3,987
Re: Model A - Light Switch Rod
Having the exact same problem with my 28 tudor. Pulled the new rod, tightend steering wheel nut, reinstalled; light switch turns with the steering wheel.
|
Forum: Model A (1928-31)
06-12-2013, 07:47 AM
|
Replies: 2
Views: 975
light and horn rod
Need help on installing new horn and light rod. Lower end is too tight to fit into top of steering column. What is best to lubricate thw new rod?
|
Forum: Model A (1928-31)
04-13-2013, 03:41 PM
|
Replies: 3
Views: 1,715
Throttle control linkage month
Just reviewed the most recent post and saw what may be my next concern. Right now I'm trying to figure out how to reattach a the throttle control assembly that was taken off 14 years ago. Any help...
|
Forum: Model A (1928-31)
04-07-2013, 04:24 PM
|
Replies: 2
Views: 1,140
Oil in steering column holes
Near the top of a 28 steering column are two holes, right and left, which appear to be an opportunity to oil both levers onthe column.
Assuming this is accurate, what type/ weight oil is best?
|
Forum: Model A (1928-31)
03-31-2013, 10:15 AM
|
Replies: 2
Views: 1,096
pressue washing gas tank
Gas tank inspection shows a a samll amount of corrosion. Has been day for at least 40 years. Have had a recommendation to wash the tank with hot soap and water, dry and followed by rinsing with...
|
Forum: Model A (1928-31)
03-26-2013, 06:42 AM
|
Replies: 10
Views: 3,126
|
Forum: Model A (1928-31)
03-19-2013, 12:42 PM
|
Replies: 8
Views: 2,618
Rebuilt water pump impeller
I am attempting to install a rebuilt water pump on to the motor of a 28 tudor.
The impeller blades are rubbing on inside of the motor. Had the bearings and packing nut professionally installed...
|
Forum: Model A (1928-31)
02-15-2013, 10:59 AM
|
Replies: 11
Views: 2,075
Re: Help with windshield installation
Had a similar experience with my 28-tudor. Two flat head screws in upper corners. Had to drillout rusted screws, clean up and retap for reattachment.
|
Forum: Model A (1928-31)
02-11-2013, 08:41 PM
|
Replies: 4
Views: 1,049
|
Forum: Model A (1928-31)
02-11-2013, 08:09 AM
|
Replies: 4
Views: 1,049
Re: Outer cover for universal joint
The front motor mount (not original style) is being replaced. This will lower the U joint .
However I still have slight misalignment with the top cover "arm" and the frame cross member. Does this...
|
Forum: Model A (1928-31)
02-05-2013, 10:54 AM
|
Replies: 4
Views: 1,049
Outer cover for universal joint
Having trouble replacing the upper half of outer cover on 28 tudor universal joint. Guard on top hits the cross frame member. Any ideas?
|