Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 80
Search took 0.01 seconds.
Search: Posts Made By: Gick70
Forum: Early V8 (1932-53) 11-29-2021, 02:32 PM
Replies: 21
Views: 992
Posted By Gick70
Re: 8BA block cracked

There is a YouTube video putting inserts in the holes and calling it a day.You could install without pulling motor.
Forum: Early V8 (1932-53) 11-29-2021, 07:32 AM
Replies: 4
Views: 239
Posted By Gick70
Re: Radiator support 48-50 vs 51-52 F1

Well I can't say anything about the support but they all take the same radiator..
Forum: Early V8 (1932-53) 11-27-2021, 05:48 PM
Replies: 7
Views: 253
Posted By Gick70
Re: 1952 f1 wiper

Looking for a electric setup,factory.
Forum: Early V8 (1932-53) 11-27-2021, 04:33 PM
Replies: 7
Views: 253
Posted By Gick70
1952 f1 wiper

Where the wipers vacuum or electric?
Forum: Early V8 (1932-53) 11-21-2021, 07:27 AM
Replies: 4
Views: 314
Posted By Gick70
Re: Flathead head gasket

Head gaskets $20-$200 range,what is recommended??
Forum: Early V8 (1932-53) 11-21-2021, 06:50 AM
Replies: 4
Views: 314
Posted By Gick70
Flathead head gasket

I noticed my exhaust pipe changed color,little more condensation,but ran fine,water gauge seemed to work. Fast forward ,noticed my radiator would form a little seepage,and a little lose of...
Forum: Early V8 (1932-53) 11-20-2021, 08:19 AM
Replies: 13
Views: 474
Posted By Gick70
Re: 1952 ford f1 heater

I have my defrost tubes in,my recurlating heater box refurbished and in place,not hooked up. I am a little concern how close the heater core is to the cardboard glovebox liner though,anybody have...
Forum: Early V8 (1932-53) 11-12-2021, 03:15 PM
Replies: 13
Views: 474
Posted By Gick70
Re: 1952 ford f1 heater

Thanks for the pictures!!
Forum: Early V8 (1932-53) 11-11-2021, 06:25 PM
Replies: 13
Views: 474
Posted By Gick70
Re: 1952 ford f1 heater

F1 mike,I realize that but,are the screws in the centerline of the vent slots in the dash?.
Forum: Early V8 (1932-53) 11-11-2021, 03:50 PM
Replies: 13
Views: 474
Posted By Gick70
Re: 1952 ford f1 heater

F1 mike,how about those measurements,where the dimples where.
Forum: Early V8 (1932-53) 11-11-2021, 03:49 PM
Replies: 13
Views: 474
Posted By Gick70
Re: 1952 ford f1 heater

I can't get to it,with the windshield in,right angle drill?
Forum: Early V8 (1932-53) 11-10-2021, 06:14 PM
Replies: 7
Views: 456
Posted By Gick70
Re: 1952 f1 radiator

I ordered one from lmc.
Forum: Early V8 (1932-53) 11-10-2021, 05:07 PM
Replies: 13
Views: 474
Posted By Gick70
1952 ford f1 heater

Can somebody give me the measurements,where the screws are located on dash that hold the defrost tubes??
Forum: Early V8 (1932-53) 11-07-2021, 10:02 AM
Replies: 1
Views: 257
Posted By Gick70
Road tool kit

I am putting together the bare essential tool box for under the seat,just in case. What did ford tool kit consist of ,back in the day?? (52 f1)
Forum: Early V8 (1932-53) 11-03-2021, 05:45 PM
Replies: 7
Views: 456
Posted By Gick70
1952 f1 radiator

Looking for a good source on a radiator,went the aluminum route radiator lasted a year,I am done with that route.
Forum: Early V8 (1932-53) 10-20-2021, 01:15 PM
Replies: 1
Views: 190
Posted By Gick70
Oil sender or gauge

I was having low pressure on my factory gauge......so I plumbed a mechanical gauge in also....initial start both gauges are the same,ten minutes if that the factory gauge drops off drastically,is it...
Forum: Early V8 06-12-2021, 05:11 PM
Replies: 2
Views: 543
Posted By Gick70
Re: F1 heater

Still looking !!!
Forum: Early V8 05-04-2021, 05:31 PM
Replies: 2
Views: 543
Posted By Gick70
Re: F1 heater

Still looking,anything ??
Forum: Early V8 01-03-2021, 12:29 PM
Replies: 0
Views: 286
Posted By Gick70
1952 f1 steering box

Looking for a box to rebuild.......
Forum: Late V8 01-03-2021, 12:26 PM
Replies: 0
Views: 547
Posted By Gick70
289 exhaust manifolds

Looking for early 289 exhaust manifolds,that exit straight back,no turns.....
Forum: Early V8 (1932-53) 12-12-2020, 09:14 PM
Replies: 2
Views: 388
Posted By Gick70
1952 ford f1,door sag

Door sag,anybody have any luck with a certain fix,drill for bigger bushings and pins,or hinge replacement?
Forum: Model A (1928-31) 09-15-2020, 05:19 PM
Replies: 14
Views: 1,233
Posted By Gick70
Re: classic auto mall

I live close by,I have been at the auto mall,it's ok. I also been on the yuengling tour many times,any info drop me a message..
Forum: Early V8 (1932-53) 08-28-2020, 08:52 PM
Replies: 17
Views: 1,238
Posted By Gick70
Re: F1-missing

I did replace with a good coil,no good...
Forum: Early V8 (1932-53) 08-28-2020, 07:31 PM
Replies: 17
Views: 1,238
Posted By Gick70
Re: F1-missing

Changing cap and rotor and putting some new wires in distributor..
Forum: Early V8 08-28-2020, 08:00 AM
Replies: 0
Views: 257
Posted By Gick70
Ford loadamatic distributor

Looking for a ford loadamatic distributor,for my 1952 f1...
Showing results 1 to 25 of 80

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:59 AM.