Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: Planojc
Forum: Early V8 (1932-53) Today, 09:55 AM
Replies: 45
Views: 1,760
Posted By Planojc
Re: transmission question

With a Mitchell you will probably still have a floor pan clearance issue, especially if you have a rumble seat.
Forum: Early V8 (1932-53) 11-24-2020, 10:24 AM
Replies: 25
Views: 935
Posted By Planojc
Forum: Early V8 (1932-53) 10-30-2020, 07:04 AM
Replies: 70
Views: 3,315
Posted By Planojc
Forum: Model A (1928-31) 10-15-2020, 08:05 AM
Replies: 11
Views: 964
Posted By Planojc
Re: Mountig Spotlight On Roadster

Anyone know of a source for the off/on switch?
Forum: Early V8 (1932-53) 09-05-2020, 08:27 AM
Replies: 20
Views: 1,031
Posted By Planojc
Re: diamondback tires

Got my Diamond Backs through Discount Tire, same price as ordering direct. They mounted and balanced them plus you get free flats fixed.
Forum: Early V8 (1932-53) 09-02-2020, 09:53 AM
Replies: 17
Views: 828
Posted By Planojc
Re: Won't go into overdrive when hot.

I have found many stock relays with as much as a two volt drop on the output going to the solenoid, due to bad connections inside the relay. If you remove the cover you will see that all connections...
Forum: Early V8 (1932-53) 08-08-2020, 09:23 AM
Replies: 7
Views: 492
Posted By Planojc
Re: Banjo Gear oil Question.

Also if you install a Mitchell overdrive, you should vent the axle due to much shorter torque tube between the banjo and the Mitchell gearbox.
Forum: Model A (1928-31) 07-22-2020, 03:25 PM
Replies: 2
Views: 250
Posted By Planojc
Re: 30-31 Roadster seat question

Thanks, you answered my question.
Forum: Model A (1928-31) 07-22-2020, 09:56 AM
Replies: 2
Views: 250
Posted By Planojc
30-31 Roadster seat question

I have new seat springs from Snyders and the backrest spring has a taper on one edge. Does the taper go on the bottom where the seat cushion meets or on the top towards the package tray?
Forum: Early V8 (1932-53) 07-22-2020, 09:09 AM
Replies: 26
Views: 1,741
Posted By Planojc
Re: Gets warm and quits running?

Vote for bad coil. Send it to Skip.
Forum: Early V8 (1932-53) 07-18-2020, 08:35 AM
Replies: 4
Views: 559
Posted By Planojc
Forum: Model A (1928-31) 07-16-2020, 11:58 AM
Replies: 9
Views: 601
Posted By Planojc
Forum: Early V8 (1932-53) 07-09-2020, 08:10 AM
Replies: 10
Views: 768
Posted By Planojc
Forum: Early V8 (1932-53) 06-29-2020, 08:26 AM
Replies: 19
Views: 1,099
Posted By Planojc
Re: Phenolic Spacer

If a spacer is used don't you have to replace the studs with longer ones?
Forum: Early V8 (1932-53) 06-02-2020, 07:39 AM
Replies: 42
Views: 1,982
Posted By Planojc
Re: Rear exit manifolds for flathead 39 Ford

I have Red's headers in my 39 standard with Brockman mellowtone mufflers.
Forum: Model A (1928-31) 05-30-2020, 07:47 AM
Replies: 7
Views: 681
Posted By Planojc
Re: Horn troubleshooting

Will it work with the horn cover off, if so, check the length of the screw that holds the cover on. If too long it will short out the brush holder.
Forum: Model A (1928-31) 02-13-2020, 11:04 AM
Replies: 9
Views: 792
Posted By Planojc
Re: REbuild Early Vacuum Wiper

I've heard of using marvel mystery oil instead of ATF.
Forum: Model A (1928-31) 01-25-2020, 11:13 AM
Replies: 1
Views: 383
Posted By Planojc

Just received a letter from the Ersland family that the Chickasha pre war meet is back on for 2020. The dates are March 20 and 21, 2020.
Forum: Early V8 (1932-53) 01-17-2020, 11:14 AM
Replies: 20
Views: 1,028
Posted By Planojc
Re: Standard or Deluxe Model?

Didn't the standard only have one horn and the deluxe with two?
Forum: Model A (1928-31) 01-16-2020, 10:27 AM
Replies: 10
Views: 873
Posted By Planojc
Re: VIN Number

JD see if the vin # on your title matches the # stamped on the engine. If it does, you are very lucky and good to go, but if not check with the Ohio DMV on what to do. You can do this online. Most of...
Forum: Early V8 (1932-53) 12-13-2019, 09:19 AM
Replies: 9
Views: 858
Posted By Planojc
Re: A Bob Drake Fuel pump...

Send it to Charlie NY
Forum: Early V8 (1932-53) 11-13-2019, 10:46 AM
Replies: 328
Views: 31,452
Posted By Planojc
Re: Interest in new restoration project thread?

Looking forward to seeing what you do on your lunch hour.
Forum: Early V8 (1932-53) 10-12-2019, 09:06 AM
Replies: 5
Views: 743
Posted By Planojc
Re: turn signals

Has anyone tried the Electro-Tech, Inc. turn signals? Operates on 6 or 12v, pos. or neg. with self canceling.
Forum: Model A (1928-31) 10-12-2019, 08:30 AM
Replies: 32
Views: 2,867
Posted By Planojc
Re: What have you found working on your A?

Changed out a model A gas gauge and the previous mechanic had wired a blue Christmas tree light bulb in place of the float.
Forum: Early V8 (1932-53) 10-09-2019, 07:48 AM
Replies: 31
Views: 2,138
Posted By Planojc
Re: Running without a torque tube center bearing ?

Put a Mitchell in it and the bearing problem is gone, plus you have overdrive.
Showing results 1 to 25 of 500

Forum Jump
Sponsored Links (Register now to hide all advertisements)

All times are GMT -5. The time now is 06:24 PM.