Forum: Early V8
09-04-2014, 07:27 PM
|
Replies: 0
Views: 1,437
1936 Ford Spare Tire Cover
SOLD - Spare tire cover for 1936 Ford Coupe Deluxe, $300.00 plus shipping. Good condition, includes lock & key, chrome hubcap, new chrome trim ring, new rubber lock ring and cover seals. Livonia...
|
Forum: Early V8 (1932-53)
08-12-2013, 01:03 PM
|
Replies: 10
Views: 2,654
Re: 1936 221 CU with Stromberg 97 stalls
Ken ct, thanks for the help. I dropped the float level down as suggested. It's a lot better now but still stalls occasionally when stopping. Also, when trying to adjust the idle mixture, the...
|
Forum: Early V8 (1932-53)
08-10-2013, 07:34 AM
|
Replies: 10
Views: 2,654
|
Forum: Early V8 (1932-53)
08-09-2013, 01:56 PM
|
Replies: 10
Views: 2,654
1936 221 CU with Stromberg 97 stalls
My 1936 221 cu flathead with a Stromberg 97 stalls when I come to a stop. I tried adjusting the float using the dry method by holding the carb upside down so the top of the float is level with the...
|
Forum: Early V8 (1932-53)
07-26-2013, 11:03 AM
|
Replies: 1
Views: 978
1936 oil pump gasket
Should there be an "O" ring or gasket installed on the oil pump where it attaches to the block of a 36 flathead? There is a circular indentation on the oil pump shaft where it slides into the block...
|
Forum: Early V8 (1932-53)
07-11-2013, 11:53 AM
|
Replies: 5
Views: 1,861
|
Forum: Early V8 (1932-53)
07-10-2013, 08:20 PM
|
Replies: 5
Views: 1,861
1936 Oil Pressure Relief Spring
Should there be a washer on the bolt/nut holding the oil pressure relief valve and spring in position on a 1936 coupe flathead? There was no washer when it was removed.
|
Forum: Early V8 (1932-53)
09-15-2012, 08:48 AM
|
Replies: 11
Views: 2,220
|
Forum: Early V8 (1932-53)
09-15-2012, 07:00 AM
|
Replies: 11
Views: 2,220
Re: 1936 21 stud head cost
I have the head but don't know where it came from, so is there a way to tell if its for a domed or flat piston?
|
Forum: Early V8 (1932-53)
09-14-2012, 01:54 PM
|
Replies: 11
Views: 2,220
|
Forum: Early V8 (1932-53)
09-14-2012, 01:29 PM
|
Replies: 11
Views: 2,220
|
Forum: Early V8 (1932-53)
08-02-2012, 08:33 AM
|
Replies: 7
Views: 1,477
|
Forum: Early V8 (1932-53)
08-01-2012, 06:27 PM
|
Replies: 7
Views: 1,477
36 5 Window Coupe Body Number
Could someone provide me with a picture showing the location of the body number tag for a 36 5 Window coupe? I have the holes in the firewall for the patent tag but not the body number tag.
Thanks.
|
Forum: Early V8 (1932-53)
05-31-2012, 09:15 AM
|
Replies: 12
Views: 2,619
Re: 35-36 Door Window Problem
Peder,
I'm currently working on my door windows for my 36 5 window. The glass was new and came with the car when I bought it about 10 years ago, so I don't know where it came from. It measures...
|
Forum: Early V8 (1932-53)
05-27-2012, 05:35 PM
|
Replies: 2
Views: 1,321
Re: 36 5 Window door channels
Thanks Tom,
I do have about a 6 foot strip of the u-channel as well. So is this u-channel only used in the upper back corner of the door, nowhere else?
Larry
|
Forum: Early V8 (1932-53)
05-27-2012, 04:21 PM
|
Replies: 2
Views: 1,321
36 5 Window door channels
I’m attempting to install new door window channel seals in my 36 5 Window Coupe. The car did not have windows when I purchased it over 10 years so I don’t have much to go on as far as old parts to...
|
Forum: Early V8 (1932-53)
05-02-2012, 07:52 AM
|
Replies: 7
Views: 1,159
Re: 36 5-window rear window seal
Thanks for the replies. This is not what I was expecting to here, I was hoping to find a lower seal. Tom, thanks for the suggestion.
|
Forum: Early V8 (1932-53)
05-01-2012, 06:33 PM
|
Replies: 7
Views: 1,159
36 5-window rear window seal
I can't seem to locate a bottom seal for the rear roll down window of my 36 5-window. I have the replacement rubber/felt glass channel and rubber bumpers but nothing for along the bottom of the...
|
Forum: Early V8 (1932-53)
03-24-2012, 01:23 PM
|
Replies: 6
Views: 1,715
|
Forum: Early V8 (1932-53)
03-24-2012, 10:23 AM
|
Replies: 6
Views: 1,715
1936 5-Window Dash/Windshield Vent
My 5-Window Coupe has what appears to be a windshield vent mounted on the left side of the dash. It has a rod attached to it under the dash to open and close the vent. Is this intended to bring in...
|
Forum: Early V8 (1932-53)
10-26-2011, 09:34 AM
|
Replies: 4
Views: 1,783
|
Forum: Early V8 (1932-53)
10-25-2011, 06:13 PM
|
Replies: 4
Views: 1,783
1936 5 Window Coupe garnish
I'm assembling a 36 5 window coupe that I bought in pieces, and I'm a little confused as to the interior garnish. To be more specific, I'm not sure how the headliner and the overhead windshield panel...
|
Forum: Early V8 (1932-53)
09-30-2011, 11:10 AM
|
Replies: 10
Views: 3,447
|
Forum: Early V8 (1932-53)
09-30-2011, 10:44 AM
|
Replies: 10
Views: 3,447
|
Forum: Early V8 (1932-53)
09-30-2011, 09:46 AM
|
Replies: 10
Views: 3,447
|