Forum: Early V8 (1932-53)
Yesterday, 10:04 PM
|
Replies: 37
Views: 1,339
|
Forum: Early V8 (1932-53)
Yesterday, 10:01 PM
|
Replies: 20
Views: 627
|
Forum: Early V8 (1932-53)
Yesterday, 06:40 PM
|
Replies: 15
Views: 546
|
Forum: Early V8 (1932-53)
01-22-2021, 09:59 PM
|
Replies: 30
Views: 1,381
Re: Calling Ol'Ron, calling Ol'Ron...
Your machinist should be able to measure your valve springs for you. You need to determine the spring seat pressure at a specific spring height. That height may or may not require shimming. Any...
|
Forum: Early V8 (1932-53)
01-21-2021, 09:30 PM
|
Replies: 20
Views: 627
|
Forum: Early V8 (1932-53)
01-18-2021, 10:20 PM
|
Replies: 30
Views: 920
|
Forum: Early V8 (1932-53)
01-18-2021, 12:33 PM
|
Replies: 33
Views: 1,603
|
Forum: Early V8 (1932-53)
01-17-2021, 03:44 PM
|
Replies: 43
Views: 919
Re: Correct replacement for Fram C181-A?
If it was me, think I would take the filter I had to a parts store and compare the length to some other filters from different sources. That would show you any differences.
|
Forum: Early V8 (1932-53)
01-16-2021, 08:42 PM
|
Replies: 43
Views: 919
|
Forum: Early V8 (1932-53)
01-15-2021, 11:51 PM
|
Replies: 43
Views: 919
|
Forum: Early V8 (1932-53)
01-14-2021, 09:57 PM
|
Replies: 39
Views: 1,521
|
Forum: Early V8 (1932-53)
01-14-2021, 09:49 PM
|
Replies: 33
Views: 1,603
|
Forum: Early V8 (1932-53)
01-14-2021, 02:25 PM
|
Replies: 5
Views: 260
Re: Q7 generator pully
Photo posted for Rex.
Note: If you are interested, the original file was 3.84 Mb, the file size limit on the Barn is around 500Kb.
|
Forum: Early V8 (1932-53)
01-13-2021, 05:01 PM
|
Replies: 19
Views: 1,808
|
Forum: Early V8 (1932-53)
01-13-2021, 02:40 PM
|
Replies: 5
Views: 260
Re: Q7 generator pully
Your photo upload issue is most likely file size, as in the file is over the limit. If you do not know how to reduce the photo files size, I can post the photo for you. Email it to me at...
|
Forum: Early V8 (1932-53)
01-11-2021, 12:02 AM
|
Replies: 16
Views: 673
Re: Crab distributor or ???
Are you attempting to run an original Ford coil on 12v? The 1.5 ohm ballast resistor is what is normally coupled with a 1.5 ohm coil. You need something in the 3.0 to 4.0 ohms total in the circuit. A...
|
Forum: Early V8 (1932-53)
01-10-2021, 05:47 PM
|
Replies: 11
Views: 365
|
Forum: Early V8 (1932-53)
01-10-2021, 05:21 PM
|
Replies: 9
Views: 537
|
Forum: Early V8 (1932-53)
01-10-2021, 05:10 PM
|
Replies: 39
Views: 1,521
Re: shipping frustration
It is going to depend on the seller. When I print a shipping label I deliver it to the shipper the same day. But, there is nothing to force the seller to do this, about all you can do is read their...
|
Forum: Early V8 (1932-53)
01-10-2021, 01:57 PM
|
Replies: 15
Views: 596
Re: Chassis question
35 to 40 frames are all basically the same with some minor differences and some different hole locations.
|
Forum: Early V8 (1932-53)
01-09-2021, 10:18 PM
|
Replies: 16
Views: 673
Re: Crab distributor or ???
The distributor doesn't care about the voltage or polarity you are using. The coil is a different story, both matter.
|
Forum: Early V8 (1932-53)
01-09-2021, 09:17 AM
|
Replies: 33
Views: 1,603
Re: who best to drop 1932 ford axle
I deal with Nostalgia Sid and Okie Joe. Okie Joe does the early axles for Sid (or did last time I talked to them).
https://droppedaxles.com/
http://www.joesspeedshop.com/joesproducts.htm
|
Forum: Early V8 (1932-53)
01-08-2021, 09:01 PM
|
Replies: 44
Views: 1,492
|
Forum: Early V8 (1932-53)
01-08-2021, 08:17 PM
|
Replies: 44
Views: 1,492
|
Forum: Early V8 (1932-53)
01-07-2021, 03:29 PM
|
Replies: 6
Views: 319
Re: Rear axle shaft loose, banjo 38
When you go to do the final assembly, be sure the tapered part of both the axle and the drum are spotless clean and dry. The nut on the axle torques down to a very high number. As you most like do...
|