Forum: Model A (1928-31)
Yesterday, 08:32 AM
|
Replies: 7
Views: 343
Re: New Coupe
First and foremost, replace the fan if its a steel original or vintage replacement. Get the Coupe's running gear and especially the brakes in good running condition. Start with the brakes, king pins,...
|
Forum: Model A (1928-31)
Yesterday, 07:52 AM
|
Replies: 9
Views: 371
Re: Water Neck Modification
I considered placing the temperature sensor in the water inlet casting, but I choose to install it in the upper radiator hose instead. My rationale is that the coolant flow in the water neck, being...
|
Forum: Model A (1928-31)
05-11-2024, 10:28 AM
|
Replies: 2
Views: 255
Re: Front bumper arm help needed
I had this problem, but I fixed it on my Model "A" by bending one arm to get equal distance to the front wheels. Loosen the front bumper clamps first. Heat the arm red hot so it bends before the...
|
Forum: Model A (1928-31)
05-10-2024, 08:59 AM
|
Replies: 8
Views: 525
Re: Temperature Gauge Issue
The needle is stuck at 140F on my Rex-A-C0 gauge. I suspect that the line from the sensor probe to the gauge has an issue. More to follow.
|
Forum: Model A (1928-31)
05-09-2024, 09:47 AM
|
Replies: 11
Views: 590
Re: New Shocks vs Rebuilt Shocks
I have 1600 miles on a professionally rebuilt set of original Houdaille shocks. All four leak and often need replenishing of their fluid!
The Houdaille shock absorber has a poor seal design, and...
|
Forum: Model A (1928-31)
05-09-2024, 07:39 AM
|
Replies: 8
Views: 525
Temperature Gauge Issue
I have a relatively new reproduction Rex-A-Co Temperature Gauge in one of my Model A's that has stopped working. Has anyone had this experience and found a fix?
|
Forum: Model A (1928-31)
05-09-2024, 07:33 AM
|
Replies: 9
Views: 544
|
Forum: Model A (1928-31)
05-06-2024, 08:55 AM
|
Replies: 10
Views: 512
Re: Gasket between carb and intake
Cork is a poor choice for sealing fluids in my opinion, because cork is porous and usually thick. Thick multi-layer gaskets cause cracking of the parts they seal because these gaskets compress under...
|
Forum: Model A (1928-31)
05-06-2024, 08:45 AM
|
Replies: 9
Views: 642
Re: oversize head gasket
My understanding is that the copper head gasket available now fits up to an 0.125 oversize cylinder bore. Maybe this is not / no longer the case?
The weakness in a big bore gasket is the minimal...
|
Forum: Model A (1928-31)
05-03-2024, 01:30 PM
|
Replies: 2
Views: 308
Re: Kick panels
Model A News magazines of the late 1960s had inserts of drawings of the various interior panels for Model A's. I am not certain, but you may find reprints of these drawings in early volumes of the...
|
Forum: Model A (1928-31)
05-03-2024, 01:21 PM
|
Replies: 38
Views: 3,045
Re: Snyder's New Catalog Came...and a Warning!
So far, the availability of essential aftermarket Model A parts I need to keep my restored Model A cars in good running condition has not negatively affected me. However, I do see a contraction in...
|
Forum: Model A (1928-31)
05-03-2024, 12:17 PM
|
Replies: 21
Views: 1,101
Re: Opinion Re Differential Gear Ratio
Thanks all for your comments. Unfortunately, I do not see my piggy bank getting enough to buy a Mitchel OD this year or in the near future. So I will likely opt for the differential gear change.
...
|
Forum: Model A (1928-31)
05-02-2024, 08:17 AM
|
Replies: 21
Views: 1,101
Opinion Re Differential Gear Ratio
My piggy bank state rules-out getting an overdrive unit, so I am considering the installation of a 3.54 gear set. The engine in my Victoria is a Model B with a 6:1 compression head, chopped flywheel...
|
Forum: Model A (1928-31)
05-02-2024, 08:04 AM
|
Replies: 9
Views: 600
Re: Hole inside front block
That hole establishes the amount of motor oil in the forward dam of the valve chamber that lubricates the front main bearing and the front camshaft bearing. The bottom of the hole should not go below...
|
Forum: Model A (1928-31)
05-02-2024, 07:47 AM
|
Replies: 38
Views: 3,045
Re: Snyder's New Catalog Came...and a Warning!
The availability of new parts is drifting back to what the market had to offer in 1960s through the 1980s. This puts pressure on us to restore more used parts like we did many years ago. The bottom...
|
Forum: Model A (1928-31)
05-01-2024, 09:48 AM
|
Replies: 11
Views: 552
Re: Source for dome light wood???
Hi Marshall! My Victoria has upholstery, so I could not get an exact measurement. However, using a tape measure over the upholstery headliner, it appears the distance is approximately 8" between the...
|
Forum: Model A (1928-31)
05-01-2024, 09:30 AM
|
Replies: 18
Views: 1,264
Re: Distributor wiring
The ignition points, the condenser and distributor casting need to have a low resistance ground path back to the battery. The slide shows how to check the ground path. Note the check is to the...
|
Forum: Model A (1928-31)
05-01-2024, 09:17 AM
|
Replies: 13
Views: 574
Re: Cowl light follow up
Hi Jay Jay! The wiring harness I use is from Bratton's. There are several configurations to choose from. Go to Page 86 of their current catalog. Here is the text from their catalog: "New Main Wiring...
|
Forum: Model A (1928-31)
05-01-2024, 08:52 AM
|
Replies: 6
Views: 352
|
Forum: Model A (1928-31)
05-01-2024, 08:44 AM
|
Replies: 13
Views: 797
|
Forum: Model A (1928-31)
04-30-2024, 10:16 AM
|
Replies: 8
Views: 719
Re: Model A Show/Swap, Trexlertown, PA, 4/28
Very nicely organized meet. Lots of Model A's on display. Excellent flea market with reasonable prices on parts. Well run food court in the firehouse and very nice pricing on the food. In the flea...
|
Forum: Model A (1928-31)
04-30-2024, 10:01 AM
|
Replies: 13
Views: 574
Re: Cowl light follow up
My Victoria has the reproduction wiring harness with the turn signals built-in. In my car, the cowl lights function as turn signals in all light switch positions, and in the parking light position....
|
Forum: Model A (1928-31)
04-30-2024, 09:33 AM
|
Replies: 11
Views: 552
Re: Source for dome light wood???
Hi Marshall. Does the wood in the pictures look like the piece of wood you need? If so, the pictures are of the dome light in my 190A Victoria which is a Murray car.
|
Forum: Model A (1928-31)
04-27-2024, 08:23 AM
|
Replies: 9
Views: 952
|
Forum: Model A (1928-31)
04-27-2024, 08:19 AM
|
Replies: 9
Views: 787
|