Forum: Early V8 (1932-53)
03-26-2024, 02:02 PM
|
Replies: 23
Views: 1,138
|
Forum: Early V8 (1932-53)
03-25-2024, 08:53 PM
|
Replies: 23
Views: 1,138
|
Forum: Early V8 (1932-53)
03-25-2024, 08:05 PM
|
Replies: 23
Views: 1,138
Re: Clutch Release Shaft Bushing tool
I purchase one of these drivers a while back from Third Gen. Here are the dimensions of the driver as well as the bushing. Maybe you can find a driver local that would work. Hope this helps.
Nate
|
Forum: Early V8 (1932-53)
03-10-2024, 03:49 PM
|
Replies: 17
Views: 753
Re: 37 Deluxe Coupe with a 11" clutch?
Terry, I appreciate your question and checked the transmission bell housing and find no witness marks where it could have been rubbing. I had no unusual noise in the driveline in the 4 years I have...
|
Forum: Early V8 (1932-53)
03-09-2024, 08:22 PM
|
Replies: 17
Views: 753
Re: 37 Deluxe Coupe with a 11" clutch?
Well, it was working fine, and since I have already replaced the ring gear and had it resurfaced, that is what I will do. Appreciate everyone's input as always. Nate Anello
|
Forum: Early V8 (1932-53)
03-08-2024, 04:08 PM
|
Replies: 17
Views: 753
Re: 37 Deluxe Coupe with a 11" clutch?
Purchased the car in 2019 and put maybe 1500 mile going to local car shows and just goofing off. Runs great. Clutch wasn't slipping but was at its adjustment limit.
|
Forum: Early V8 (1932-53)
03-08-2024, 03:42 PM
|
Replies: 17
Views: 753
37 Deluxe Coupe with a 11" clutch?
So, from a recent previous post you may know that I pulled my 21-stud engine and transmission from my 37 Coupe. I did this to reseal both and resurface the flywheel and replace the clutch and...
|
Forum: Early V8 (1932-53)
03-04-2024, 08:02 PM
|
Replies: 18
Views: 978
|
Forum: Early V8 (1932-53)
02-28-2024, 10:02 AM
|
Replies: 18
Views: 978
|
Forum: Early V8 (1932-53)
02-28-2024, 08:24 AM
|
Replies: 18
Views: 978
|
Forum: Early V8 (1932-53)
02-27-2024, 06:11 PM
|
Replies: 18
Views: 978
|
Forum: Early V8 (1932-53)
02-26-2024, 06:57 PM
|
Replies: 18
Views: 978
|
Forum: Early V8 (1932-53)
02-26-2024, 03:56 PM
|
Replies: 18
Views: 978
|
Forum: Early V8 (1932-53)
02-26-2024, 01:48 PM
|
Replies: 0
Views: 140
37 21 Stud Crank Pulley Torque Spec
After searching the past post and looking at the Van Pelts chart, I don't see a torque spec for the crank pulley bolt. Some of the later engines in past post say 45 to 55 foot pound. Is that spec...
|
Forum: Early V8 (1932-53)
02-05-2024, 05:32 PM
|
Replies: 4
Views: 618
|
Forum: Early V8 (1932-53)
02-03-2024, 03:10 PM
|
Replies: 4
Views: 618
|
Forum: Early V8 (1932-53)
01-30-2024, 01:02 PM
|
Replies: 33
Views: 2,190
Re: Probably the wrong auction venue for this car.
I agree with some but not all of the responses. Having seen the car in person makes a difference in the judgment of the car. Forgive my ignorance for not knowing about the incorrect fender skirts and...
|
Forum: Early V8 (1932-53)
01-28-2024, 07:59 PM
|
Replies: 33
Views: 2,190
|
Forum: Early V8 (1932-53)
01-28-2024, 07:16 PM
|
Replies: 33
Views: 2,190
Probably the wrong auction venue for this car.
Saw this 36 Roadster sell at the Barrett Jackson auction in Scottsdale this week.
Sold for $30,000. plus $3,000.00 buyer's premium. Had a couple of small paint issues that would be easy to correct....
|
Forum: Early V8 (1932-53)
10-30-2023, 07:45 PM
|
Replies: 16
Views: 1,236
Re: Bolt buster /induction heater
I bought an Induction Innovations - Mini-Ductor Venom HP (MDV-787) several months ago. Used it with great success to remove exhaust bolts. Worked great for me and was happy with the results. Not...
|
Forum: Early V8 (1932-53)
09-17-2023, 06:06 PM
|
Replies: 6
Views: 727
Re: Waldrons exhaust system (Aluminized Steel)
I have aluminized steel exhaust that was installed over 25 years ago on a 69 Camaro SS that still looks brand new. I took it back to the exhaust shop a couple years ago to have a small repair done on...
|
Forum: Early V8 (1932-53)
08-31-2023, 06:44 PM
|
Replies: 23
Views: 1,773
|
Forum: Early V8 (1932-53)
08-02-2023, 07:49 PM
|
Replies: 31
Views: 1,884
Re: 4 Post car lift
I have had an Advantage 9000 Pound 4 Post Lift for 6 years and have had zero issues. I would recommend this company to anyone.
...
|
Forum: Early V8 (1932-53)
06-28-2023, 04:00 PM
|
Replies: 7
Views: 746
Re: 37 Deluxe Coupe Floor Pans
I'll for sure let you know. I just didn't see a lot of options. I was going to buy a bead roller but didn't think I'd use it more than once. If I was doing a concourse restoration, I'd explore other...
|
Forum: Early V8 (1932-53)
06-28-2023, 07:01 AM
|
Replies: 7
Views: 746
Re: 37 Deluxe Coupe Floor Pans
Well, after searching for other suppliers of floor pans for my 37, I found another company,
Classic 2 Current Fabrication that sells US made pans. From the pictures, the pattern looks close. They...
|