Forum: Early V8 (1932-53)
04-05-2024, 09:30 PM
|
Replies: 4
Views: 1,142
|
Forum: Early V8 (1932-53)
07-20-2023, 04:37 PM
|
Replies: 13
Views: 928
|
Forum: Early V8 (1932-53)
07-20-2023, 12:09 PM
|
Replies: 13
Views: 928
|
Forum: Early V8 (1932-53)
07-16-2023, 03:42 PM
|
Replies: 13
Views: 928
Re: Alternator replacement
I read the fan mounted generator pulley (G420) was not produced by Ford? May have an aftermarket part produced to allow the use of latter generator on a earlier fan mounted generator application? Can...
|
Forum: Early V8 (1932-53)
07-16-2023, 02:59 AM
|
Replies: 13
Views: 928
Re: Alternator replacement
The shaft is keyed but the stamped steel pulley I pulled off was just screwed on (no key) flush with the armature shaft? I've noticed the cast iron pulley (G420) also threaded leaves enough threads...
|
Forum: Early V8 (1932-53)
07-15-2023, 02:19 PM
|
Replies: 13
Views: 928
Alternator replacement
Fellas, purchased a recently rebuilt converted 12 Volt flathead generator a few years ago that came with what appears to be a stamped steel smooth pulley. I have a cast iron fan mounted (G420)...
|
Forum: Early V8 (1932-53)
05-21-2023, 07:17 AM
|
Replies: 7
Views: 647
|
Forum: Early V8 (1932-53)
05-20-2023, 04:16 PM
|
Replies: 7
Views: 647
|
Forum: Early V8 (1932-53)
05-20-2023, 01:49 PM
|
Replies: 7
Views: 647
Crab distributor vacuum advance.
Fellas, attempting to break in and tune fresh built 59A. Noticed around a 100 rpm fluctuation at idle which is reduced to a 25 rpm fluctuation when I unhook and plug the vacuum advance. Wondering if...
|
Forum: Early V8 (1932-53)
05-20-2023, 10:51 AM
|
Replies: 2
Views: 628
Re: Canadian Aluminum heads
Thanks for the info! I have not measured the transfer volume but during visual inspection they appear identical.
|
Forum: Early V8 (1932-53)
05-19-2023, 09:56 PM
|
Replies: 2
Views: 628
Canadian Aluminum heads
Guys picked up a set of Canadian 24 stud heads at swap meet. One is a C91A the other C99A. Any ideas what the difference is? Thanks fellas!
|
Forum: Early V8 (1932-53)
04-15-2023, 08:43 PM
|
Replies: 17
Views: 1,716
|
Forum: Early V8 (1932-53)
04-15-2023, 10:37 AM
|
Replies: 17
Views: 1,716
|
Forum: Early V8 (1932-53)
04-14-2023, 09:19 PM
|
Replies: 17
Views: 1,716
|
Forum: Early V8 (1932-53)
04-14-2023, 04:05 PM
|
Replies: 17
Views: 1,716
|
Forum: Early V8 (1932-53)
04-14-2023, 01:23 PM
|
Replies: 17
Views: 1,716
|
Forum: Early V8 (1932-53)
04-14-2023, 01:06 PM
|
Replies: 17
Views: 1,716
|
Forum: Early V8 (1932-53)
04-14-2023, 12:03 PM
|
Replies: 17
Views: 1,716
Fresh build issues?
Hey guys, freshly built 59 block, 3 & 5/16, merc crank, potvin 3/8 cam, new Edelbrock heads. Fired up fine. Good oil pressure. Left side 160 degrees. Right side 180 degrees and climbing fairly fast....
|
Forum: Early V8 (1932-53)
02-23-2023, 03:00 AM
|
Replies: 11
Views: 798
|
Forum: Early V8 (1932-53)
02-22-2023, 12:48 PM
|
Replies: 11
Views: 798
|
Forum: Early V8 (1932-53)
02-22-2023, 07:03 AM
|
Replies: 11
Views: 798
|
Forum: Early V8 (1932-53)
02-21-2023, 01:23 PM
|
Replies: 11
Views: 798
|
Forum: Early V8 (1932-53)
02-21-2023, 11:13 AM
|
Replies: 11
Views: 798
1934 Crank Handle Bearing Guide - 59A
When mounting a 59A in a 34 ford does the Crank Handle Bearing Guide interfere with the crankshaft pulley or bolt? This is the ring piece that the spring bolts run across on top of the crossmember....
|
Forum: Early V8 (1932-53)
01-09-2023, 08:55 PM
|
Replies: 4
Views: 771
|
Forum: Early V8 (1932-53)
01-09-2023, 07:00 PM
|
Replies: 4
Views: 771
Two piece oil pan in a 34?
I am aiming to use the two piece (truck) 59a oil pan on my 1934 with original wishbones. Wondered if anyone on here has tried this application? If so did you experience any clearance issues or did it...
|