Forum: Model A (1928-31)
08-18-2021, 06:42 PM
|
Replies: 33
Views: 7,213
Re: More kudos to Bert's Model A Center
I second the second! I have ordered from Bert's multiple times in the last couple of months and parts are always shipped same-day and arrive from CO to KY in 2 days. Very satisfied with the quality...
|
Forum: Model A (1928-31)
08-14-2021, 11:12 AM
|
Replies: 20
Views: 4,012
Re: Flywheel Housing Check
Hello all! Just thought I would update this thread with the results for future reference. I think I had a couple of issues. A couple of the pressure plate fingers were WAY out of adjustment for...
|
Forum: Model A (1928-31)
08-03-2021, 11:53 AM
|
Replies: 5
Views: 665
Re: Output Shaft Play
Very good point Tom and I did verify that the shaft was the later type that requires the round spacer. Perhaps that led to the omission when rebuilt by the PO.
|
Forum: Model A (1928-31)
08-03-2021, 11:27 AM
|
Replies: 5
Views: 665
Re: Output Shaft Play
Well, I think this one is a wrap! Disassembled the transmission this morning and as suspected the spacer on the output shaft pilot was missing! I did confirm it was a "short" bearing. Nothing in...
|
Forum: Model A (1928-31)
08-02-2021, 07:14 PM
|
Replies: 5
Views: 665
Re: Output Shaft Play
Yes, the joint is tight and I can see the movement of the output shaft inside the case and I am certain it is moving and the input (main drive) shaft is not (fore and aft).
Guess it will be coming...
|
Forum: Model A (1928-31)
08-02-2021, 06:41 PM
|
Replies: 5
Views: 665
Output Shaft Play
Finally was able to get around to tearing down my '29 to address the severe clutch judder that has been present since I have owned the car. It's looking like the issue (hopefully) was severe...
|
Forum: Model A (1928-31)
07-29-2021, 03:14 AM
|
Replies: 16
Views: 2,717
|
Forum: Model A (1928-31)
04-10-2021, 07:35 AM
|
Replies: 20
Views: 4,012
Re: Flywheel Housing Check
Thank you Brent for your detailed reply, certainly seems to make sense. Hopefully I just have some clutch or transmission issues and not something more foundational such as crank misalignment.
|
Forum: Model A (1928-31)
04-08-2021, 10:54 PM
|
Replies: 20
Views: 4,012
Re: Flywheel Housing Check
Thanks everyone! Some great food for thought. I will definitely be checking the pressure plate adjustment and go from there. Hopefully it's just the fingers. I do like the channel locks approach,...
|
Forum: Model A (1928-31)
04-08-2021, 08:32 AM
|
Replies: 20
Views: 4,012
Flywheel Housing Check
Good day all! My '29 roadster has had some pretty severe clutch chatter in 1st and reverse and a slight vibration since I have owned it. Ordered a long feeler gauge to check the finger adjustment,...
|
Forum: Model A (1928-31)
07-24-2020, 10:12 PM
|
Replies: 3
Views: 1,188
Re: Front Engine Mount Post Length
Thanks so much! Turns out mine was a little short, and on closer inspection had been repaired in the past. Ordered a replacement and all went together without drama. Thanks for the help!
|
Forum: Model A (1928-31)
07-20-2020, 03:03 PM
|
Replies: 3
Views: 1,188
Front Engine Mount Post Length
Curious how long the threaded post should be on a front engine yoke. I suspect mine may have been sheared off and filed, since it seems a little short and has no cotter pin hole. It was mounted...
|
Forum: Model A (1928-31)
06-30-2020, 08:04 PM
|
Replies: 2
Views: 1,478
Front Motor Mount Removal
Getting ready to replace the cheesy aftermarket mount with the proper setup, I have loosened the rear mounts and removed the throttle linkage. I have not yet removed the yoke to see what clearance I...
|
Forum: Model A (1928-31)
11-20-2019, 12:14 PM
|
Replies: 11
Views: 3,754
|
Forum: Model A (1928-31)
11-20-2019, 10:56 AM
|
Replies: 11
Views: 3,754
Re: Remove/Replace Headlight Reflector
Thanks again everyone! The lighting is pretty bad where I have the car stored, looking closer this morning I could see the tabs at 3 and 9 that I had to unbend. Now I just need to deal with a...
|
Forum: Model A (1928-31)
11-20-2019, 08:30 AM
|
Replies: 11
Views: 3,754
|
Forum: Model A (1928-31)
11-20-2019, 07:04 AM
|
Replies: 11
Views: 3,754
Remove/Replace Headlight Reflector
I am probably overlooking the obvious, but I didn't want to force anything - how do you remove the headlight reflectors from the headlight bucket?
|
Forum: Model A (1928-31)
06-07-2019, 06:22 PM
|
Replies: 61
Views: 11,954
Re: Will I fit in a Roadster??
Thanks everyone for all of the interesting commentary - regarding both diet and roadsters! I am happy to report that I do indeed fit comfortably in my new (to me) roadster! As discussed, entry with...
|
Forum: Model A (1928-31)
05-22-2019, 08:58 PM
|
Replies: 61
Views: 11,954
Will I fit in a Roadster??
I am afraid I may have gotten the cart before the proverbial horse, but I am in the process of purchasing a nice '29 roadster to fulfill a lifelong dream. I have spent some time with a '30 tudor...
|
Forum: Model T (1909-1927)
06-29-2015, 09:54 AM
|
Replies: 5
Views: 1,818
Re: Anyone Recognize these Fenders?
I think you are probably correct, I was just hopeful they were off-the shelf. Very nice work in any case, looks like they have the bead and a wire edge. I also really like the small cowl.
|
Forum: Model T (1909-1927)
06-28-2015, 06:53 PM
|
Replies: 5
Views: 1,818
|
Forum: Model T (1909-1927)
06-27-2015, 08:43 PM
|
Replies: 5
Views: 1,818
Anyone Recognize these Fenders?
Curious if anyone knows the origin of the open fenders on the speedster for sale at the link below? Would love to find some for a speedster project.
http://car-from-uk.com/sale.php?id=93143
|
Forum: Model-T
06-26-2015, 10:17 AM
|
Replies: 0
Views: 1,524
Wanted - Good High Radiator
Looking for a decent high radiator for a '26 driver. Willing to pick up within 100 miles of Cincy or happy to work with you to ship.
|