Forum: Model A (1928-31)
03-18-2012, 08:00 AM
|
|
Replies: 347
Views: 202,594
Re: F150 tranny with overdrive
For anyone interested,,, Snyders has provided for me a floor mat for my 29 coupe that hasn't been trimmed, they special ordered it from the manufacturer. There are no holes cut and the outside edges...
|
|
Forum: Model A (1928-31)
02-17-2012, 10:01 AM
|
|
Replies: 347
Views: 202,594
Re: F150 tranny with overdrive
I was wondering if anyone has found a source for floor mats without the hales pre-punched. I have e-mailed Snyders to see if they could special order one for me.
|
|
Forum: Model A (1928-31)
01-07-2012, 09:14 AM
|
|
Replies: 347
Views: 202,594
Re: F150 tranny with overdrive
Anyone have a photo of the throw-out return spring arrangement? The instructions I have say to hook it over the lower opening of the inspection hole. Seems that would be pulling it up as much as...
|
|
Forum: Model A (1928-31)
09-17-2011, 03:44 PM
|
|
Replies: 347
Views: 202,594
Re: F150 tranny with overdrive
How do you measure RPM while in motion, do you have a dash mounted tach. or some other way? If so what drives the tach.
|
|
Forum: Model A (1928-31)
09-14-2011, 06:42 AM
|
|
Replies: 347
Views: 202,594
Re: F150 tranny with overdrive
Correction,,, actually the 91A7563 has the weights, the 8N or 9N 7563 do not. The 91A7563 is listed as a heavy duty replacement for these tractors.
|
|
Forum: Model A (1928-31)
09-13-2011, 07:08 AM
|
|
Replies: 347
Views: 202,594
Re: F150 tranny with overdrive
The 26 it is.
By the way, if anyone needs a V8 clutch, it's exactly the same as the one used in an older Ford tractor (8N, 9N, 600, and 800) The part numbers are 91A7563 pressure plate, 8N 7550...
|
|
Forum: Model A (1928-31)
09-10-2011, 07:58 AM
|
|
Replies: 347
Views: 202,594
Re: F150 tranny with overdrive
While on the subject of ratios, there are three overdrive ratios for the Ford transmission, 26.7%, 37.9% and 41.1%. I have a 26 and a 41, I think the 41 would be too high, so I'm probable going with...
|
|
Forum: Model A (1928-31)
09-09-2011, 10:06 AM
|
|
Replies: 347
Views: 202,594
|
|
Forum: Model A (1928-31)
09-09-2011, 08:04 AM
|
|
Replies: 347
Views: 202,594
Re: F150 tranny with overdrive
I have the short AA bell housing, although it's not yet installed, it looks like it will only require the pilot be shortened about a half inch.. This transmission has about i 3/16 inch pilot past the...
|
|
Forum: Model A (1928-31)
09-08-2011, 05:43 PM
|
|
Replies: 347
Views: 202,594
Re: F150 tranny with overdrive
I started gathering parts for the 150 transmission install a while back. I now have a couple of RTS boxs, had a friend with a good machine shop shorten the mainshaft. I shortened the drive shaft and...
|
