Forum: Model A (1928-31)
06-24-2016, 08:38 AM
|
Replies: 1
Views: 1,543
30 AA coming together
Set the cab today. Hood and doors are next, then the interior, then drive the tires off of it. ...
|
Forum: Model A (1928-31)
06-15-2016, 08:57 PM
|
Replies: 12
Views: 2,244
Re: Elbow grease, sheet metal work, and paint
Thanks. I got into the gas tank welting with the buffer. Did not take but a second to take the paint off of it. Touched it up though and barely noticeable. Just when you think you are done........
|
Forum: Model A (1928-31)
06-15-2016, 06:47 PM
|
Replies: 12
Views: 2,244
Elbow grease, sheet metal work, and paint
This 30 AA body was covered in Kool Seal and red paint. The rust out areas required replacement. The body was so rusted I was afraid to sandblast. $1500+ was not in the budget for a better...
|
Forum: Model A (1928-31)
06-12-2016, 04:39 PM
|
Replies: 1
Views: 1,562
30 AA progress
Enjoying the time and laughs with my Dad, but sand, sand, sand. I don't have a paint booth, and the humidity in North Alabama is about 101%. My clear coat clouded up. Sanding for second coat of...
|
Forum: Model A (1928-31)
05-09-2016, 12:31 PM
|
Replies: 7
Views: 2,466
|
Forum: Model A (1928-31)
05-09-2016, 07:09 AM
|
Replies: 7
Views: 2,466
|
Forum: Model A (1928-31)
05-09-2016, 07:08 AM
|
Replies: 7
Views: 2,466
|
Forum: Model A (1928-31)
05-06-2016, 06:17 PM
|
Replies: 7
Views: 2,466
Original vs homemade wood 30 AA
Rear header is complete and reproduced the missing wood over curved roof panel. Had one original for pattern. Not too bad!! Buying the front header....
|
Forum: Model A (1928-31)
05-01-2016, 04:12 PM
|
Replies: 6
Views: 1,712
|
Forum: Model A (1928-31)
05-01-2016, 08:23 AM
|
Replies: 6
Views: 1,712
Is there a thicker radiator for an AA?
I have installed the radiator shell on the AA. It had a steel, painted commercial shell when I got it, put very pitted. I didn't notice a gap between the front of the shell and the radiator. I...
|
Forum: Model A (1928-31)
04-23-2016, 08:42 PM
|
Replies: 9
Views: 1,965
|
Forum: Model A (1928-31)
04-23-2016, 07:03 PM
|
Replies: 9
Views: 1,965
|
Forum: Model A (1928-31)
04-18-2016, 06:41 AM
|
Replies: 1
Views: 1,176
|
Forum: Model A (1928-31)
04-15-2016, 06:01 PM
|
Replies: 1
Views: 1,176
30 AA Truck Gas Tank Filler Strip
What is the piece called that resembles a dash panel, only screws to the pillar posts on the outside just above the gas tank? Is it reproduced?
|
Forum: Model A (1928-31)
04-12-2016, 05:25 AM
|
Replies: 14
Views: 7,557
|
Forum: Model A (1928-31)
04-11-2016, 08:30 PM
|
Replies: 14
Views: 7,557
|
Forum: Model A (1928-31)
04-11-2016, 07:16 PM
|
Replies: 9
Views: 3,615
Re: What color is this???
Of course, it is hard to use the chips in the Paint and Finish Guide with the chips on a white background. Blue Rock Green looked the closest.
|
Forum: Model A (1928-31)
04-11-2016, 07:00 PM
|
Replies: 9
Views: 3,615
What color is this???
I am beginning to disassemble the cab on the 30 AA. The cab had been painted in the past with what looks like Cool Seal. Bad shape. However, I pulled the dash panel and found what looks like...
|
Forum: Model A (1928-31)
04-10-2016, 07:46 PM
|
Replies: 5
Views: 2,038
Dad's maiden ride in the 30 AA
Pop's maiden voyage in his almost complete 30 AA Ford Truck today. This 67 year old man was like a kid in a candy shop. From helping me with math homework as a kid, spending hours playing tic-tac-toe...
|
Forum: Model A (1928-31)
04-10-2016, 06:59 PM
|
Replies: 8
Views: 2,074
|
Forum: Model A (1928-31)
04-10-2016, 05:53 PM
|
Replies: 8
Views: 2,074
|
Forum: Model A (1928-31)
04-09-2016, 07:19 PM
|
Replies: 8
Views: 2,074
|
Forum: Model A (1928-31)
04-07-2016, 07:02 PM
|
Replies: 4
Views: 1,530
|
Forum: Model A (1928-31)
04-07-2016, 05:57 PM
|
Replies: 4
Views: 1,530
Spark help
I wired up a test setup for my new engine. Ignition wire from dist to one side of the coil. A jumper wire with alligator clips from the other coil side to the - on battery. Jumper wire is serving...
|
Forum: Model A (1928-31)
04-06-2016, 07:09 PM
|
Replies: 7
Views: 1,936
Re: Distributor smoking
That explains it. It's been a few years since I wired up to test an engine. Thank you for your help!!!
|