Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: Ronnie
Forum: Early V8 (1932-53) 11-22-2021, 10:40 AM
Replies: 3
Views: 381
Posted By Ronnie
Re: Cracked Valve Seat

here is another discussion https://fordbarn.com/forum/showthread.php?t=190808


R
Forum: Early V8 (1932-53) 11-05-2021, 10:06 AM
Replies: 30
Views: 1,403
Posted By Ronnie
Re: Flathead Timing Gear Failure?

Make sure the air valve in the compression tester is the correct one they are not the same as a tire valve uses. Using a standard valve doesn't work.


Ronnie
Forum: Early V8 (1932-53) 07-21-2021, 10:39 AM
Replies: 16
Views: 984
Posted By Ronnie
Re: new valve seats for a 53 EAC

Find a shop with a Winona PH-2000 or a Serdi mach they can fit the block.
https://www.jalopyjournal.com/forum/threads/flathead-valve-seat-machine.627796/

look in the above post there is a reply...
Forum: Early V8 (1932-53) 07-12-2021, 03:37 PM
Replies: 3
Views: 893
Posted By Ronnie
Re: I need some canadian help

What us the web page "url" Kayweb doesn't find anything???


R
Forum: Early V8 (1932-53) 07-02-2021, 09:04 AM
Replies: 19
Views: 1,379
Posted By Ronnie
Re: Condolences for John W. Lawson .....

John (JWL) Sorry for your loss. May your brother "RIP"



Ronnie
Forum: Early V8 (1932-53) 07-02-2021, 08:38 AM
Replies: 19
Views: 992
Posted By Ronnie
Re: Piston opinions

Will here is the distributor list scroll down to canada and see results.
https://uempistons.com/c-29-silv-o-lite.html


There are 20+ ERI members in BC.ERI is dedicated to machine shops only....
Forum: Early V8 (1932-53) 07-01-2021, 10:03 PM
Replies: 19
Views: 992
Posted By Ronnie
Re: Piston opinions

Will D They only sell through their existing suppliers. They should be available at Lordco if not any ERI machine shop they all have access to United Machine.What part of BC are u in?



R
Forum: Early V8 (1932-53) 07-01-2021, 09:39 AM
Replies: 19
Views: 992
Posted By Ronnie
Re: Piston opinions

Yes all seen under options are united mach products.


R
Forum: Early V8 (1932-53) 06-30-2021, 08:28 PM
Replies: 19
Views: 992
Posted By Ronnie
Re: Piston opinions

Here is a good piston

https://uempistons.com/series-3888-silv-o-lite-ford-239-3-9-1058.html


https://uempistons.com/

United machine is a player

R
Forum: Early V8 (1932-53) 06-28-2021, 09:47 PM
Replies: 31
Views: 1,748
Posted By Ronnie
Re: Need Advice on Removing Broken off Stud and Head

There are wheel studs that you can purchase that are spark plug thread,make a puller from that thread it into spark plug hole use a slide hammer on it to lift head.


R
Forum: Early V8 (1932-53) 06-27-2021, 10:22 PM
Replies: 31
Views: 1,555
Posted By Ronnie
Forum: Early V8 (1932-53) 06-27-2021, 10:18 PM
Replies: 31
Views: 1,748
Posted By Ronnie
Re: Need Advice on Removing Broken off Stud and Head

No need to fool around with a spark plug to cobble up a threaded item to make a puller

There is a good selection of metric wheel studs available,get a couple and fab one up. Used in newer Gm...
Forum: Early V8 (1932-53) 05-30-2021, 01:15 PM
Replies: 16
Views: 1,169
Posted By Ronnie
Re: Bypass Oil Filters

Restrictor is in the outlet

https://ph.baldwinfilters.com/baldwin/en/baldwin-spin-on-lube-filters/b164


r
Forum: Early V8 (1932-53) 04-11-2021, 11:56 AM
Replies: 62
Views: 5,013
Posted By Ronnie
Re: How to repair damage to a deck

Read again jwl had a comment


R
Forum: Early V8 (1932-53) 04-08-2021, 09:25 AM
Replies: 9
Views: 1,070
Posted By Ronnie
Re: No oil pressure on new build

Pre oil with a garden sprayer. Works well for what you want to attempt.


https://ls1tech.com/forums/generation-iii-internal-engine/1640877-oil-priming.html scroll down to see the set up.


R
Forum: Early V8 (1932-53) 04-08-2021, 09:13 AM
Replies: 62
Views: 5,013
Posted By Ronnie
Re: How to repair damage to a deck

Unless you are an accomplished weldor the sucess rate is very slim.The welds usually produce hard spots in cast.That refuse anything but grinding. I would try this first no real after effects with...
Forum: Early V8 (1932-53) 04-01-2021, 01:27 PM
Replies: 38
Views: 2,519
Posted By Ronnie
Re: TIG welder recomendations

Do you have a dollar limit established. That is a big factor.


R
Forum: Early V8 (1932-53) 03-19-2021, 08:05 PM
Replies: 83
Views: 5,979
Posted By Ronnie
Forum: Early V8 (1932-53) 03-10-2021, 09:03 PM
Replies: 83
Views: 5,979
Posted By Ronnie
Re: Trouble shoot 1950 8Ba initial start up Help

It appears the horse has left the barn.


R
Forum: Early V8 (1932-53) 03-06-2021, 10:11 PM
Replies: 21
Views: 1,625
Posted By Ronnie
Re: I'd like to start a new thread on the components we choose for an engine build

Where are u going to buy gaskets? Auto value or lordco will treat you right.
Victor and fel pro still make full sets.Go into any machine shop and they will get what you need.


R
Forum: Early V8 (1932-53) 02-25-2021, 07:37 PM
Replies: 83
Views: 5,979
Posted By Ronnie
Re: Trouble shoot 1950 8Ba initial start up Help

Is yours like this? If so the cam is in correct R
Forum: Early V8 (1932-53) 02-25-2021, 04:05 PM
Replies: 236
Views: 17,682
Posted By Ronnie
Re: WHO Is the Oldest Early V8 Forum Member?

Here I am 8.602325267042627



R
Forum: Early V8 (1932-53) 02-21-2021, 12:53 PM
Replies: 11
Views: 1,146
Posted By Ronnie
Re: High hp flathead build posted 20 hrs ago

I agree the numbers are a stretch for sure. Also look at the way the engine stand head is bolted to the engine,that's a little different.His statement about oil flow is also incorrect but that has...
Forum: Early V8 (1932-53) 02-16-2021, 09:10 AM
Replies: 45
Views: 3,537
Posted By Ronnie
Forum: Early V8 (1932-53) 01-02-2021, 11:55 AM
Replies: 16
Views: 933
Posted By Ronnie
Re: Resize pics using windows paint

Tub my win 10 still has paint same as Win 7.



R
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:15 PM.