Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.08 seconds.
Search: Posts Made By: Terry,OH
Forum: Early V8 (1932-53) Today, 10:13 AM
Replies: 3
Views: 132
Posted By Terry,OH
Forum: Early V8 (1932-53) Today, 06:45 AM
Replies: 3
Views: 132
Posted By Terry,OH
34 radio installation and operating manual

I see there is a reproduction of a 34 radio installation manual. The reproduction instructions I have seen say "All In One" Is this for the glove box radio or the ash tray? I am looking for exact...
Forum: Early V8 (1932-53) Today, 06:06 AM
Replies: 8
Views: 332
Posted By Terry,OH
Re: 21 stud engine best upgrades?

35 engine used the 48 Carb. which is slightly larger. The reason Ford went to the he 97 was better economy.
Forum: Early V8 (1932-53) Today, 06:03 AM
Replies: 4
Views: 156
Posted By Terry,OH
Re: Shift lever position / modification

Not easily reversed, the shift lever has to be removed and heated red hot at the base and bent slightly. It's not a hard job but would have to replace the lever with another to get it back to...
Forum: Early V8 (1932-53) 04-20-2021, 06:23 AM
Replies: 23
Views: 1,124
Posted By Terry,OH
Re: Rear shocks on a 1936 fordor

Make sure you have the proper 36 rear shocks before sending them out for rebuild. Over the years many things get changed.
Forum: Early V8 (1932-53) 04-20-2021, 06:14 AM
Replies: 27
Views: 606
Posted By Terry,OH
Re: 34 smoking starter switch from the newbie.

Beside checking the wire connections check the extension of the switch that goes into the car floor. Yours looks to be home made. Be sure when you depress the extension with your foot the switch is...
Forum: Early V8 (1932-53) 04-19-2021, 07:18 AM
Replies: 3
Views: 274
Posted By Terry,OH
Re: Columbia O/D

140W only NAPA sells it as SL 24238. Use the Columbia fill plug only and fill till it comes out of the plug hole. Then with the rear wheel off the ground, trans in high and Columbia in high run for...
Forum: Early V8 (1932-53) 04-18-2021, 11:30 AM
Replies: 48
Views: 1,293
Posted By Terry,OH
Re: Covid

My best wishes to your family!
Forum: Early V8 (1932-53) 04-18-2021, 06:28 AM
Replies: 31
Views: 2,343
Posted By Terry,OH
Re: 1940 Ford convertible body tags

Like woodiedude in #10 above here is another early firewall you can see the four holes for mounting the patent data plate over the hand throttle bump out, on the vertical surface. Ill ask the...
Forum: Early V8 (1932-53) 04-15-2021, 06:53 PM
Replies: 3
Views: 276
Posted By Terry,OH
Re: United oil bath air cleaner.

Appears like the early HD oil bath air cleaner for some of the 21 stud engines. Do you have a question?
Forum: Early V8 (1932-53) 04-15-2021, 06:49 PM
Replies: 15
Views: 948
Posted By Terry,OH
Re: 1938 Temperature Gauge

See posting #9 above You can search them on the web. They are in Willoughby, OH
Forum: Early V8 (1932-53) 04-15-2021, 06:43 PM
Replies: 8
Views: 442
Posted By Terry,OH
Forum: Early V8 (1932-53) 04-15-2021, 12:51 PM
Replies: 26
Views: 566
Posted By Terry,OH
Forum: Early V8 (1932-53) 04-15-2021, 07:29 AM
Replies: 14
Views: 379
Posted By Terry,OH
Re: 33 Cabriolet window frame "support rod"

At my local hardware store and they did have sleeve or tube nuts. At the time I did not look to see if they had 8-32 or if they were brass and plated or in steel. Having them drilled through is not...
Forum: Early V8 (1932-53) 04-14-2021, 07:23 AM
Replies: 14
Views: 379
Posted By Terry,OH
Re: 33 Cabriolet window frame "support rod"

I had the same problem on a 35. I used brass countersink head screws and had them drilled through, tapped and the threads removed. The countersink angle did not match the frame and the heads had to...
Forum: Early V8 (1932-53) 04-12-2021, 06:21 AM
Replies: 3
Views: 321
Posted By Terry,OH
Re: Put remote coil back still no spark

If you have 6V on the red power wire to the distributor and with the spark plug wires removed, car in neutral, with E brake on, turn the engine over by hand and watch the voltmeter, if it goes to 3...
Forum: Early V8 (1932-53) 04-11-2021, 07:31 AM
Replies: 2
Views: 390
Posted By Terry,OH
Re: oil pressure sender, 38 sedan

Can test the sender using air hook up a battery and use the gauge. Older senders can become plugged with dry sludge from the engine oil. The sludge can be cleaned out without damage to the senders...
Forum: Early V8 (1932-53) 04-11-2021, 06:39 AM
Replies: 10
Views: 536
Posted By Terry,OH
Re: Day out in the 33

Read your article in the V8 Times. Very good trip. Did you get the other engines fixed?
Forum: Early V8 (1932-53) 04-11-2021, 06:36 AM
Replies: 13
Views: 1,771
Posted By Terry,OH
Re: Vacuum reading

The vacuum gauge is not simply a go or nogo gauge it should also be used to adjust the carburetor idle mixture adjustment screws. Under the same conditions you took your reading just slowly turn the...
Forum: Early V8 (1932-53) 04-11-2021, 06:26 AM
Replies: 7
Views: 310
Posted By Terry,OH
Re: Coil readings what it it telling me

What your readings are telling you is Skips original coil is 6V and needs the Ford series resistor. Your aftermarket coil is also 6V and does not need the Ford resistor. Both coils look good to go....
Forum: Early V8 (1932-53) 04-10-2021, 09:07 AM
Replies: 14
Views: 775
Posted By Terry,OH
Re: spark plug wires

Original inner caps are marked with the cylinder numbers 1-4 on the R, 5-8 on the L
Forum: Early V8 (1932-53) 04-09-2021, 02:25 PM
Replies: 6
Views: 514
Posted By Terry,OH
Re: Shackle pin, heads up

Unusual to see plating of any sort on the shackles
Forum: Early V8 (1932-53) 04-08-2021, 08:36 AM
Replies: 12
Views: 562
Posted By Terry,OH
Re: '40 Steering Lock Disassembly Follow Up?

The internal steering shaft removed from the column?
Forum: Early V8 (1932-53) 04-08-2021, 08:17 AM
Replies: 4
Views: 380
Posted By Terry,OH
Re: Found my miss,,BUT

Idle mixture screws nearly all out?? Sounds like a Carb issue.
Forum: Early V8 (1932-53) 04-07-2021, 09:21 AM
Replies: 20
Views: 637
Posted By Terry,OH
Re: 33 ignition switch

Yes you are correct the plate is not used on the 33-34 ignition switch. My memory is corrected. Thank You Sheldon and David.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:11 PM.