Forum: Early V8 (1932-53)
Yesterday, 05:42 PM
|
Replies: 5
Views: 379
|
Forum: Early V8 (1932-53)
Yesterday, 12:43 PM
|
Replies: 17
Views: 511
|
Forum: Early V8 (1932-53)
04-17-2024, 05:49 PM
|
Replies: 6
Views: 300
|
Forum: Early V8 (1932-53)
04-17-2024, 06:43 AM
|
Replies: 17
Views: 511
|
Forum: Early V8 (1932-53)
04-16-2024, 08:03 PM
|
Replies: 17
Views: 511
Re: Door weatherstripping 40 coupe
The top piece goes on the body, not the door. The "foot" of the "L" extends out, away from the body. It does not tuck in the channel. It begins just above the upper door hinge and runs back to the B...
|
Forum: Early V8 (1932-53)
04-16-2024, 07:23 AM
|
Replies: 50
Views: 1,618
|
Forum: Early V8 (1932-53)
04-15-2024, 10:58 AM
|
Replies: 5
Views: 379
|
Forum: Model A (1928-31)
04-13-2024, 01:03 PM
|
Replies: 4
Views: 251
|
Forum: Model A (1928-31)
04-13-2024, 10:47 AM
|
Replies: 4
Views: 251
'31 pickup rear fender filler panels
Hello folks...
Okay, I admit I am lost.
I am attempting to figure out where the filler panels get attached to the fenders.
Rear fenders (you knew that) on a '31 pickup truck.
I have nice...
|
Forum: Early V8 (1932-53)
04-12-2024, 04:09 PM
|
Replies: 7
Views: 317
Re: Need a copy of body mounts for 47 coupe
Ralph, I'd done a concourse restoration on a '46 coupe a few years back and like you, was forced to cut open the rockers to access the caged nuts. Not too bad when the body was on the rotisserie...
|
Forum: Early V8 (1932-53)
04-11-2024, 06:30 PM
|
Replies: 11
Views: 410
|
Forum: Early V8 (1932-53)
04-10-2024, 08:01 PM
|
Replies: 11
Views: 410
Re: Removing caps on '37 hubcaps?
I actually carefully tape that area after the first coat of paint has been applied.
Place the stainless cap on a suitably sized plastic bucket with a thin towel draped over the edge to install the...
|
Forum: Early V8 (1932-53)
04-10-2024, 02:05 PM
|
Replies: 6
Views: 270
|
Forum: Early V8 (1932-53)
04-10-2024, 01:32 PM
|
Replies: 11
Views: 410
|
Forum: Early V8 (1932-53)
04-10-2024, 11:37 AM
|
Replies: 6
Views: 270
Re: Door mechanism Washers
I don't believe so.
External tooth or internal tooth lock washers are available for certain but both, again, I don't believe so.
Do you know the ID and OD of the washers you desire?
|
Forum: Early V8 (1932-53)
04-10-2024, 10:50 AM
|
Replies: 2
Views: 346
Re: Back Home
Phil, anyone that has dealt with you knows you are reliable and well worth the wait.
|
Forum: Early V8 (1932-53)
04-09-2024, 08:26 AM
|
Replies: 10
Views: 1,198
Re: 1936 Ford Cabriolet Top Boot
Many, perhaps most, were destroyed.
Keep in mind that LB had patterns for not only Fords, but MANY makes and models.
A loss to history for certain.
|
Forum: Early V8 (1932-53)
04-09-2024, 08:22 AM
|
Replies: 4
Views: 406
|
Forum: Early V8 (1932-53)
04-09-2024, 07:59 AM
|
Replies: 25
Views: 1,068
|
Forum: Early V8 (1932-53)
04-08-2024, 11:29 AM
|
Replies: 25
Views: 1,068
|
Forum: Early V8 (1932-53)
04-08-2024, 09:34 AM
|
Replies: 25
Views: 1,068
|
Forum: Early V8 (1932-53)
04-07-2024, 06:14 PM
|
Replies: 25
Views: 1,068
|
Forum: Early V8 (1932-53)
04-07-2024, 01:32 PM
|
Replies: 15
Views: 1,196
Re: Adjustable Lifters
Ron, The last set I got from Red's had three of the sixteen that were dead soft. I am so glad I had the sense and means to check them prior to installing.
|
Forum: Early V8 (1932-53)
04-06-2024, 04:12 PM
|
Replies: 6
Views: 411
Re: original Ford wheel paint
Ford was in the business of making a profit while building reasonably priced vehicles. Primer application costs money. And truly, the paint on the rims held up rather well without primer.
|
Forum: Early V8 (1932-53)
04-06-2024, 11:28 AM
|
Replies: 6
Views: 411
|