Forum: Model A (1928-31)
06-02-2023, 12:24 PM
|
|
Replies: 1
Views: 451
|
|
Forum: Early V8 (1932-53)
05-16-2023, 10:35 PM
|
|
Replies: 39
Views: 5,295
Re: Wheel Cylinder issues
Thank you for the reply. It's been a couple of years since I ran those lines. Maybe I did use solid copper washers rather than copper crush washers. I hate getting old. I knew all this stuff...
|
|
Forum: Early V8 (1932-53)
05-16-2023, 08:35 AM
|
|
Replies: 39
Views: 5,295
Re: Wheel Cylinder issues
Another F1 front cylinder question. Does anyone know if there is supposed to be an adapter between the brake line and the cylinder port? I bought new wheel cylinders and rubber lines from NAPA and...
|
|
Forum: Model A (1928-31)
08-28-2022, 07:11 PM
|
|
Replies: 13
Views: 18,612
|
|
Forum: Early V8 (1932-53)
03-29-2022, 05:34 AM
|
|
Replies: 11
Views: 1,118
Re: Got a gearbox?
Strange that I should run across this thread just after seeing one of these on Cleveland, TN FB. Looks to be complete, outside is crusty but the interior is very clean. ID# is 54-23176 or 54-23I76....
|
|
Forum: Early V8 (1932-53)
01-25-2022, 02:35 PM
|
|
Replies: 3
Views: 686
Re: 92/81 Carbs
@deuce lover and @ deuce roadster, thank you for the replies. Maybe I've finally lucked out. Fellow I bought them off of had four he had thought about using on a 4 x 2 manifold he had but then...
|
|
Forum: Early V8 (1932-53)
01-25-2022, 12:10 PM
|
|
Replies: 3
Views: 686
92/81 Carbs
I have read and understand that the 81 carbs came on the V8 60 engine. Will two 81's work on stock 59AB and if not, why do so many people seem to want them?
|
|
Forum: Early V8 (1932-53)
01-03-2022, 09:31 PM
|
|
Replies: 5
Views: 1,106
Re: Block boring
I don't know where you are in AL but if you're anywhere Chattanooga, Roberts and Sons, 4285 Bonny Oaks Dr., Chattanooga, TN, 423 698 4097, is the place to go. I've been very pleased with their work....
|
|
Forum: The Test Forum
01-03-2022, 09:19 PM
|
|
Replies: 3
Views: 15,856
Re: '35-'36 W/8BA Fan
Do you think it would be possible to modify this fan setup for a 59AB? With the stock fan mount as low as it can go, the fan blades are going to run into the bottom of the upper radiator hoses about...
|
|
Forum: Early V8 (1932-53)
10-27-2020, 08:17 PM
|
|
Replies: 69
Views: 9,917
Re: Rust Oleum spray cans
I have several spray cans of Rustoleum that I've had for more than two years. About 9 months ago, I turned the cans upside down and every month after that, I would alternate turning them right side...
|
|
Forum: Early V8 (1932-53)
02-12-2020, 04:04 PM
|
|
Replies: 24
Views: 4,424
Re: Looking for a new job-maybe...
Mac. I think your idea of a weekend training session on rebuilding transmissions, or anything else you would want to share, would be great. If you decide to do so, I would like to be there. You've...
|
|
Forum: Early V8 (1932-53)
06-12-2019, 12:37 PM
|
|
Replies: 11
Views: 4,542
|
|
Forum: Early V8 (1932-53)
04-28-2019, 12:46 PM
|
|
Replies: 8
Views: 1,294
Re: 41 merc v8 oil pressure
I'll take it that you don't have an oil filter. I plugged the port that would have normally supplied the oil filter, removed the 6v sender and installed a mechanical gauge. I think the new gauge...
|
|
Forum: Early V8 (1932-53)
12-21-2018, 02:50 PM
|
|
Replies: 76
Views: 21,205
Re: Bearing clearance
Not trying to hi-jack this thread but, I have a large quantity of NOS rod and main bearings that came out of a Ford dealers inventory when they were declared obsolete. There are floaters and later...
|
|
Forum: Early V8 (1932-53)
10-03-2018, 09:15 AM
|
|
Replies: 16
Views: 3,459
Re: Is this radiator salvageable? (cost wise)
The determining factor in my decision to replace the original radiator in my '48 Merc with aluminum was cost. $600+ to re-core locally as opposed to $204 from Champion with free shipping. It was...
|
|
Forum: Early V8
07-02-2018, 02:52 PM
|
|
Replies: 0
Views: 730
1936 Ford Sedan Right Front Fender
Looking for a good 36 sedan RF fender. Shop we took the car to for restoration conveniently "lost" ours during the year they had it and did nothing and won't make good on it.
Alan Purvis
|
|
Forum: Early V8 (1932-53)
03-12-2018, 12:02 PM
|
|
Replies: 24
Views: 5,198
Re: Electric engine fan
If I'm in the wrong forum for this, please let me know. I'm a newby and I just went through a semi-trailer full of NIB and used flathead parts. One of the Dynamatic fans was in the mix. It was new...
|
