Forum: Model A (1928-31)
03-29-2024, 12:33 AM
|
Replies: 12
Views: 552
|
Forum: Model A (1928-31)
02-25-2024, 12:56 PM
|
Replies: 25
Views: 1,927
Re: fuel shelf life in tank
I have had different results; We left 2 or 3 A's in the unheated garage in MI for 6 months while we did the snow bird thing- for 15 years. I did nothing but pull the fuse and go. Reg. pump gas, at...
|
Forum: Model A (1928-31)
08-01-2023, 07:34 PM
|
Replies: 23
Views: 2,568
|
Forum: Model A (1928-31)
06-27-2023, 04:32 PM
|
Replies: 7
Views: 1,052
Re: Nu Rex automatic timing
I have the device on my 2 cars and they are good around town in stop and start driving--no need to change gear as much. At highway speeds they don't make much difference. I like them. JR
|
Forum: Early V8
04-30-2023, 12:31 PM
|
Replies: 0
Views: 361
600-16 coker blackwalls
Almost new 600-16 Coker blacks--almost new- I bought my F1 and the tires looked too small for my eye. pick-up preferred
|
Forum: Early V8 (1932-53)
04-26-2023, 02:53 PM
|
Replies: 9
Views: 1,075
|
Forum: Early V8 (1932-53)
04-26-2023, 08:52 AM
|
Replies: 9
Views: 1,075
Re: Fuel pressure-confussion
I got the info from Fomoco owners manual and the Fomoco Ford 1949-50-51-52 F1 series trucks Shop Manual---Both are available as reprints. JR
|
Forum: Early V8 (1932-53)
04-25-2023, 07:48 PM
|
Replies: 9
Views: 1,075
Fuel pressure-confussion
Hey Guru's, The Ford "repair manuals " from the day, recommends a fuel pressure of 3 1/2 to 4 1/2 psi at the carb. The discussion on this site seems to to guide one to a MUCH lower pressure. What am...
|
Forum: Model A (1928-31)
04-01-2023, 04:57 PM
|
Replies: 41
Views: 10,535
Re: Edison's Model A picture from Gilmore Museum
one more bit of info about the #1 phaeton. When I was a youth, in the 50"s, the #1 engine sat is the Henry Ford Museum, on an engine stand, along with the picture of Henry stamping the engine. The...
|
Forum: Model A (1928-31)
03-25-2023, 01:09 PM
|
Replies: 41
Views: 10,535
Re: Edison's Model A picture from Gilmore Museum
one more bit of info about the #1 phaeton. When I was a youth, in the 50"s, the #1 engine sat is the Henry Ford Museum, on an engine stand, along with the picture of Henry stamping the engine. The...
|
Forum: Early V8 (1932-53)
03-24-2023, 10:50 AM
|
Replies: 3
Views: 542
fuel pressure question
Hey guys, 1952 F1- std. Flathead. one ford 94 carb--What fuel pressure is best? I've got 3.5 lbs. about what the ford repair manual wants. A lot of the posts on this forum suggests much less. What...
|
Forum: Early V8 (1932-53)
10-23-2022, 04:27 PM
|
Replies: 10
Views: 1,937
|
Forum: Early V8 (1932-53)
10-22-2022, 05:32 PM
|
Replies: 10
Views: 1,937
Bonded brake linings failed !
Hey, 1952 F1 new ( Abt. 4000 MI.) bonded lining on one rear wheel started to drag and get hot. I started to smell the heat, drove home,abt 2 mi., pulled the drum and the linings fell out on the...
|
Forum: Early V8 (1932-53)
06-30-2022, 03:54 PM
|
Replies: 26
Views: 3,475
|
Forum: Early V8
02-01-2022, 04:14 PM
|
Replies: 0
Views: 436
wanted- oil filter for EAB
I would like to purchase a complete system ( tank that bolts to head, lines, metering thingy, etc ) as ford delivered it. Thanks , Jerry
|
Forum: Early V8 (1932-53)
01-30-2022, 02:38 PM
|
Replies: 3
Views: 776
|
Forum: Early V8 (1932-53)
01-29-2022, 05:18 PM
|
Replies: 3
Views: 776
What is this for?
I have a EAB block. It has a grease fitting on the drivers side- just above the oil pan- about 6" from the back of the block. What is it for??? What would need to be greased when all that oil is in...
|
Forum: Early V8 (1932-53)
12-12-2021, 11:06 AM
|
Replies: 7
Views: 905
Re: 1952 F1 starting problem
all connections are good--over size cables. It seems like the starter doesn't have as much torque when warm. ??? Jerry
|
Forum: Early V8 (1932-53)
12-11-2021, 06:17 PM
|
Replies: 7
Views: 905
1952 F1 starting problem
Barners; My 51-F1 EAB/ 6 volt starter spins fast and starts fast when cold, after running for 10-15 miles won't spin fast enough to start, let it set for an hour and it's fine again. What is going...
|
Forum: Early V8 (1932-53)
01-14-2021, 07:01 PM
|
Replies: 1
Views: 794
Newbie question -52 F1
I,ve lubed all on my 52 F1 but the the rear axle has a sealed roller bearing. 69 years old? Is the old grease still viable? Should I change the bearings?
|
Forum: Early V8
12-14-2020, 08:32 AM
|
Replies: 0
Views: 467
|
Forum: Model A (1928-31)
09-04-2020, 08:10 AM
|
Replies: 32
Views: 7,439
|
Forum: Early V8
07-25-2020, 06:42 PM
|
Replies: 0
Views: 436
|
Forum: Early V8 (1932-53)
06-23-2020, 09:03 AM
|
Replies: 8
Views: 1,496
|
Forum: Early V8 (1932-53)
06-22-2020, 02:55 PM
|
Replies: 8
Views: 1,496
holly 94 rebuild kit
Hey, I have a rebuild kit for the Holley 94. I has 2 power valves--one has a movable shaft and the other has a fixed shaft. What is the difference in the valves- I have a 1952 F1- EAB block, which...
|