Forum: Model A (1928-31)
10-06-2021, 06:19 PM
|
Replies: 23
Views: 2,888
Re: Stymied
back to the electronic distributor ,10 turns out on choke rod needle valve runs good above 1000 RPMS. wont idle yet but that will happen.
I dont know what I did. the coil gets hot but I can hold my...
|
Forum: Model A (1928-31)
10-05-2021, 12:50 PM
|
Replies: 23
Views: 2,888
Re: Stymied
running 12v neg ground.
blew all the carbs out and rotated them in today same problem reinstalled stock points distributor same problem. I still think I have a large vacuum leak that I cannot find....
|
Forum: Model A (1928-31)
10-05-2021, 07:37 AM
|
Replies: 23
Views: 2,888
Re: Stymied
I tried 3 carbs all reacted the same! I made sure there was no excess pipe beyond ferrel. ???
|
Forum: Model A (1928-31)
10-05-2021, 07:32 AM
|
Replies: 23
Views: 2,888
|
Forum: Model A (1928-31)
10-04-2021, 06:43 PM
|
Replies: 23
Views: 2,888
Re: Stymied
i installed a regular point distributor. no change, sameproblem. new exhaust system from Ecklers
|
Forum: Model A (1928-31)
10-04-2021, 06:40 PM
|
Replies: 23
Views: 2,888
|
Forum: Model A (1928-31)
10-04-2021, 04:19 PM
|
Replies: 23
Views: 2,888
Re: Stymied
3/4 pulled out.it would not run untill I relaced the distributor
|
Forum: Model A (1928-31)
10-04-2021, 02:36 PM
|
Replies: 23
Views: 2,888
Stymied
1930 stock ModelA out of 20 years dry storage. fresh gas, rebuilt Zenith 2 carb.
New gaskets head and intake/exhaust,carb.
50 pounds compression each cylinder
Strong gas flow.
Electronic ignition...
|
Forum: Model A (1928-31)
09-17-2021, 03:16 PM
|
Replies: 4
Views: 864
|
Forum: Model A (1928-31)
09-06-2021, 11:31 AM
|
Replies: 20
Views: 2,669
Re: wont fire
is the timing dimple also the recess for the timing pin?
|
Forum: Model A (1928-31)
09-04-2021, 12:45 PM
|
Replies: 20
Views: 2,669
|
Forum: Model A (1928-31)
09-03-2021, 04:26 PM
|
Replies: 20
Views: 2,669
|
Forum: Model A (1928-31)
09-03-2021, 04:24 PM
|
Replies: 20
Views: 2,669
|
Forum: Model A (1928-31)
09-03-2021, 12:02 PM
|
Replies: 20
Views: 2,669
wont fire
after 20 years storage. I started this model a and it ran rough (mising,back fires) changed distributor because plastic on the old points failed.
timed with the front pin.
have compression,...
|
Forum: Model A (1928-31)
06-15-2021, 02:32 PM
|
Replies: 4
Views: 854
oil slinger
I am cofused on the location and installation of the oil slinger. HELP!!
The mechanics Handbook is no help
|
Forum: Model A (1928-31)
03-10-2021, 01:54 PM
|
Replies: 1
Views: 1,008
|
Forum: Model A (1928-31)
11-13-2020, 01:47 PM
|
Replies: 2
Views: 1,213
|
Forum: Model A (1928-31)
11-12-2020, 01:57 PM
|
Replies: 4
Views: 1,335
|
Forum: Model A (1928-31)
11-12-2020, 01:22 PM
|
Replies: 11
Views: 2,095
2 tooth adjustment
I dont under stand how the adjustments work in agemmer two tooth steering gear.
|
Forum: Model A (1928-31)
08-08-2020, 05:26 PM
|
Replies: 13
Views: 1,351
|
Forum: Model A (1928-31)
08-08-2020, 08:10 AM
|
Replies: 13
Views: 1,351
12v amps gauge
can I use a stock 6v amps gauge in 12v neg ground system?
|
Forum: Model A (1928-31)
12-06-2019, 06:16 PM
|
Replies: 3
Views: 2,046
zenith 1
what does the cap jet do? there is a main jet for high speed. does the idle adjustment screw only control air? If so how does fuel get to the throat at Idle?
|
Forum: Model A (1928-31)
11-26-2019, 12:02 PM
|
Replies: 41
Views: 5,888
12 volt coil with resistor
will a 12v coil with resistor send 12v to the points? I don't understand if the resistor lowers voltage or ohms
|
Forum: Model A (1928-31)
11-26-2019, 11:56 AM
|
Replies: 11
Views: 2,074
Re: parts for tillotson
[QUOTE=f balsiger;1824829]where can I get a rebuild kit for tillotson round bowl carburetor (f1-B)
|
Forum: Model A (1928-31)
11-24-2019, 01:56 PM
|
Replies: 11
Views: 2,074
|