Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 433
Search took 0.03 seconds.
Search: Posts Made By: SAJ
Forum: Model A (1928-31) 05-03-2021, 04:33 PM
Replies: 39
Views: 1,949
Posted By SAJ
Re: Max Speed of a Model A with 26% OD and HC Head

Correction to my post above about Larry's question. I was told there are 1200 registered Model A's in NZ.
And the belief is there may be about the same number or more unregistered, hiding in barns...
Forum: Model A (1928-31) 05-01-2021, 06:00 PM
Replies: 30
Views: 1,517
Posted By SAJ
Re: 6.1 Head / Carburetor Choice

We have a Tudor and a Roadster both with 5.5 heads and Zenith model B carbs on drilled out A manifolds, with large K& N air cleaners fitted. Both cars will go well over 70 mph flat out and return...
Forum: Model A (1928-31) 04-28-2021, 06:10 AM
Replies: 17
Views: 669
Posted By SAJ
Re: How often does a Model A have a need for a tow truck?

After high speed runs through the hilly turns to Napier city, I pulled up to the first roundabout and, as I tried to turn, the steering wheel came up towards me and the car went straight on. I...
Forum: Model A (1928-31) 04-24-2021, 06:51 AM
Replies: 39
Views: 1,949
Posted By SAJ
Re: Max Speed of a Model A with 26% OD and HC Head

Larry, my electronic balancer is just an old Italian Corghi. Nothing special. It has the usual cone mountings which are no good for a Model A, plus adjustable 4 and 5 stud mountings for the...
Forum: Model A (1928-31) 04-23-2021, 02:49 AM
Replies: 39
Views: 1,949
Posted By SAJ
Re: Max Speed of a Model A with 26% OD and HC Head

Larry, your wheels must be better than the ones we see in NZ. I have an electronic balancer that mounts the wheels through the 5 stud holes. I have balanced many front wheels that were bouncy at as...
Forum: Model A (1928-31) 04-20-2021, 03:31 AM
Replies: 20
Views: 901
Posted By SAJ
Re: Undercarriage Detailing

I would just sand the lumpy spots smooth, looking for cracks or holes, and if none are found, hit it with black enamel aerosol. I use Plasticote gloss black enamel aerosols. On the muffler I sand...
Forum: Model A (1928-31) 04-16-2021, 02:31 AM
Replies: 100
Views: 10,636
Posted By SAJ
Re: The new Burtz Mosel A engine

Bearing crush is very important and checked by installing the bolt or bolts on only one side of the cap, whereupon the gap left on the opposite side between the cap faces can be measured with feeler...
Forum: Model A (1928-31) 03-18-2021, 05:11 AM
Replies: 46
Views: 2,335
Posted By SAJ
Re: Mitchell O.D.

Synchro, I have to push or pull my Mitchel o/d gearstick very positively when warm, with no delay or pause with synchronizing pressure on the stick before the the baulk ring balls "pop" through....
Forum: Model A (1928-31) 03-08-2021, 05:30 AM
Replies: 41
Views: 3,869
Posted By SAJ
Re: Synthetic Oil for Model A

Model A Ron, all of the Mobil 1oils I see listed contain both zinc and phosphorous in the form of ZDDP.
The lowest phosphorous is 650 ppm and the highest is way up at 1750. I use 15W50 which has...
Forum: Model A (1928-31) 03-03-2021, 05:51 AM
Replies: 87
Views: 5,964
Posted By SAJ
Re: 4 post lift

I have a 4 post English Bradbury. Instead of rolling transverse jacks, it has two extra longitudinal beams that adjust sideways on small rollers supported on two lateral beams. These beams rise and...
Forum: Model A (1928-31) 03-03-2021, 05:32 AM
Replies: 41
Views: 3,869
Posted By SAJ
Re: Synthetic Oil for Model A

KenBolton, I have an image in my head of a motor with sludge containing years of unfiltered metal particles from normal wear processes, plus cotton fibres released from a worn cam gear and maybe...
Forum: Model A (1928-31) 02-03-2021, 05:37 AM
Replies: 89
Views: 4,561
Posted By SAJ
Re: A question for old guys

700 RPM. I understand your problem. I too am 76. I was very active until about 70, when osteo arthritis got much worse in shoulders. I cannot raise my right arm much above horizontal unless I lift it...
Forum: Model A (1928-31) 01-29-2021, 03:10 AM
Replies: 14
Views: 1,334
Posted By SAJ
Re: fan blade disaster

He is Bruce Stratton. Email brucestratton@xtra.co.nz. I paid about NZD$175.00 for mine.
They are a carbon fibre thing of beauty.
SAJ in NZ
Forum: Model A (1928-31) 01-08-2021, 04:48 PM
Replies: 20
Views: 1,340
Posted By SAJ
Re: Bendix Drive Question??

Nkaminar, thanks for the reply. That is most interesting and I hope it turns up a better part that I have not seen or heard of. My barrels did come from Snyders, the last one probably about 7 or 8...
Forum: Model A (1928-31) 01-06-2021, 12:29 AM
Replies: 28
Views: 1,310
Posted By SAJ
Re: Where do I go from here??

One thing I would definitely check before driving it is that the rear hub bolts are fully tight and the hubs pulled up on the tapers. My roadster was run with them loose, as if adjusted for taper...
Forum: Model A (1928-31) 01-06-2021, 12:05 AM
Replies: 20
Views: 1,340
Posted By SAJ
Re: Bendix Drive Question??

Hi Doug. I hope you and Nan are staying safe from this awful virus. Diane Dave and Karen send their regards too. We will miss you at the Gisborne rally coming up soon.
I have done about 50000 miles...
Forum: Model A (1928-31) 01-05-2021, 06:15 PM
Replies: 20
Views: 1,340
Posted By SAJ
Re: Bendix Drive Question??

Thanks Terry. Even a 5/32 spacer would prevent the starter spigot from centralising in the flywheel cover register, meaning only the 3 bolts would hold it central. Are they "fitted" bolts i wonder?...
Forum: Model A (1928-31) 01-05-2021, 04:32 AM
Replies: 20
Views: 1,340
Posted By SAJ
Re: Bendix Drive Question??

Nkaminar, you show the USA ones that we are breakiing. They come from Snyders. The Indian made ones are even more fragile.
That Snyders barrel drive is what is in my photos. There is no spring in...
Forum: Model A (1928-31) 01-04-2021, 04:24 PM
Replies: 20
Views: 1,340
Posted By SAJ
Re: Bendix Drive Question??

Nkaminar, did you by any chance photograph your modern drive before you put it in? I would like to get one like you have, but do not see such available anywhere.
I have broken the slotted collar on...
Forum: Model A (1928-31) 01-04-2021, 06:29 AM
Replies: 20
Views: 1,340
Posted By SAJ
Re: Bendix Drive Question??

I have had many problems with both Indian made drives and recently a Weldon USA one.
The problem is shown in the pics attached of two starters side by side with standard bendix and Weldon barrel...
Forum: Model A (1928-31) 12-28-2020, 06:21 PM
Replies: 26
Views: 1,466
Posted By SAJ
Re: Mode A Piston expander/ knurling tool to Buy

The alternative to knurling is Koetherizing, wherein the piston is squeezed through the gudgeon bores by a bolt and thrust bearings into a more cammed shape on the thrust faces. While under this...
Forum: Model A (1928-31) 12-28-2020, 05:25 PM
Replies: 9
Views: 573
Posted By SAJ
Re: Wood rot - wood hardener

SAJ here Synchro. We make fillers for rotten and broken wood in houses. For cosmetic and weathering purposes but not for structural or strength repairs.
We just developed a water based wood...
Forum: Model A (1928-31) 12-26-2020, 09:28 PM
Replies: 28
Views: 1,940
Posted By SAJ
Re: Spark plug socket

Further to "box wrench" we call hexagonal tube wrenches "box spanners", or some times "tube spanners" because they are made from formed seamless tubing. But tube spanners can also be those open ended...
Forum: Model A (1928-31) 12-14-2020, 03:37 PM
Replies: 28
Views: 1,995
Posted By SAJ
Re: Gland rings

Brent, I have not used JB weld Extremeheat. My comments are only from the view of an industrial chemist who has formulated similar products many years ago. And to correct the statements that it is an...
Forum: Model A (1928-31) 12-13-2020, 05:13 AM
Replies: 6
Views: 872
Posted By SAJ
Re: Counterbalanced Crank with a harmonic balancer

You can hear torsional vibration with metal timing gears which shake together as you pass through the harmonic rev ranges.
SAJ in NZ
Showing results 1 to 25 of 433

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:33 AM.