Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 239
Search took 0.02 seconds.
Search: Posts Made By: briphaeton
Forum: Model A (1928-31) 01-25-2021, 02:58 PM
Replies: 15
Views: 1,369
Posted By briphaeton
Re: Piston and cylinder clearance / measurement???

Does Forged pistons require more clearance?
Forum: Model A (1928-31) 01-10-2021, 07:13 AM
Replies: 12
Views: 1,242
Posted By briphaeton
Forum: Model A (1928-31) 11-27-2020, 03:17 PM
Replies: 12
Views: 1,371
Posted By briphaeton
Re: MAFCA Puzzle

It's a change in the number of puzzle pieces, which you can change back if wanted.
Forum: Model A (1928-31) 10-31-2020, 11:22 AM
Replies: 26
Views: 8,870
Posted By briphaeton
Re: Adjusting ahooga horn

Sparton 8/32 x 13/16
Forum: Model A (1928-31) 10-30-2020, 10:11 AM
Replies: 2
Views: 691
Posted By briphaeton
Re: Upholstery instructions

The MAFCA coupe book has the sport coupe top information and it's probably the same.
Forum: Model A (1928-31) 09-27-2020, 10:55 AM
Replies: 9
Views: 959
Posted By briphaeton
Re: Refitting Rods- Sunnen Hone

I have one but never tried using it.
Forum: Model A (1928-31) 09-13-2020, 10:32 AM
Replies: 14
Views: 838
Posted By briphaeton
Re: Early 60-A 2-window Fordor Sedans

My sedan doesn't have windshield vents like other Model A's, that's were the side vent was needed and probably helped delayed production of the fordor. The dash is flat with no screws holding it on.
Forum: Model A (1928-31) 09-13-2020, 10:14 AM
Replies: 14
Views: 838
Posted By briphaeton
Re: Early 60-A 2-window Fordor Sedans

I've had my July 28 for 30 years and seldom see 28 fordor's with LS cowl vent at National Meets. I don't think they had right vents. Factory photo's highlight left side vents, upside down handles,...
Forum: Model A (1928-31) 09-12-2020, 04:48 PM
Replies: 14
Views: 838
Posted By briphaeton
Re: Early 60-A 2-window Fordor Sedans

My is a July 28 with a left hand side cowl vent. Are you looking for a right hand drive car?
Years ago my friend had a early roadster with cowl vents on both sides (surely not original)
Forum: Model A (1928-31) 08-01-2020, 04:03 PM
Replies: 21
Views: 1,527
Posted By briphaeton
Re: using a 12 volt system with the 6 volt horn

What I use is a Ohmite RESISTOR, 2 OHM, 100 WATT, ADJ TUBULAR, WIREWOUND, +-10% TOLERANCE.The Galco part number is D100K2ro.
It is a adjustable resister so you get adjust what sound you want from...
Forum: Model A (1928-31) 06-30-2020, 10:37 AM
Replies: 29
Views: 5,988
Posted By briphaeton
Re: Ammco brake shoe chart

thank you KR500 !!!
bri1930phaeton@gmail.com
Forum: Model A (1928-31) 06-16-2020, 04:34 PM
Replies: 11
Views: 1,268
Posted By briphaeton
Re: starter update

What solenoid did you use?
Forum: Model A (1928-31) 06-04-2020, 01:54 PM
Replies: 2
Views: 1,278
Posted By briphaeton
Re: A&L Ford Parts

A&L Parts Specialties
- Allen Lepore PO Box 301
Canton CT 06019 860-693-2620
860-693-0112 Fax
Forum: Model A (1928-31) 05-28-2020, 12:46 PM
Replies: 15
Views: 1,458
Posted By briphaeton
Re: KR Wilson Groover

Thanks Terry.
Easily made made from high speed round stock, probably 5/16? Notice the relief angles on top and sides. Machinist call them form tools and sharpen using a abrasive honing stone.
Forum: Model A (1928-31) 05-25-2020, 07:45 PM
Replies: 15
Views: 1,458
Posted By briphaeton
Re: KR Wilson Groover

You make your own cutter out of some 1/4 high speed steel stock. Most machine tool shop sell. It will need to be shaped using a grinder to match the groove needed.
Forum: Model A (1928-31) 05-25-2020, 01:25 PM
Replies: 9
Views: 905
Posted By briphaeton
Re: RPMs increase when engage Laycock overdrive, hmmm?

The transmission switch takes it out of overdrive if you try to go into reverse gear while in overdrive, because that would damage the overdrive. You need to change the plate on the dash switch that...
Forum: Model A (1928-31) 05-24-2020, 05:01 PM
Replies: 9
Views: 905
Posted By briphaeton
Re: RPMs increase when engage Laycock overdrive, hmmm?

You need to switch the on to off and the off to on. My speedometer and tach drops while in overdrive.
Forum: Model A (1928-31) 05-07-2020, 09:54 PM
Replies: 22
Views: 2,761
Posted By briphaeton
Re: Lighting for speedometer and gas gauge

I would like to get a LED bulb so it would get so hot.
Forum: Model A (1928-31) 04-15-2020, 02:46 PM
Replies: 33
Views: 4,335
Posted By briphaeton
Re: CAD Model of Model A Engine

I would be interested in scale of 1/5, I would like to machine a scale model a engine.
Thanks Brian
Forum: Model A (1928-31) 04-09-2020, 10:38 PM
Replies: 94
Views: 19,898
Posted By briphaeton
Re: What is the hardest Model A accessory to find

perfect to top off your motor meter
Forum: Model A (1928-31) 04-04-2020, 01:14 PM
Replies: 8
Views: 1,051
Posted By briphaeton
Re: Rear main oil pan seal

I've used the over sized cork that I put a beveled edge on so it squeezes into place.
Forum: Model A (1928-31) 03-27-2020, 02:32 PM
Replies: 16
Views: 1,999
Posted By briphaeton
Re: Is My Cam Going Flat?

I've used the rule of 9 on my Miller also but recently picked up a P & G valve gapping tool.
I'm looking forward to trying it out.
https://www.ctci.org/pg-valve-gapper-model-111-instructions/
Forum: Model A (1928-31) 03-24-2020, 01:27 PM
Replies: 27
Views: 2,468
Posted By briphaeton
Re: What Year Is This Coupe ?

Those are Ardun heads on a flathead Ford V8
Forum: Model A (1928-31) 03-17-2020, 07:01 PM
Replies: 17
Views: 2,227
Posted By briphaeton
Re: Dohc miller/schofield/cragar head info

Check out
https://www.museumofamericanspeed.com/miller200.html
Forum: Model A (1928-31) 02-28-2020, 09:07 PM
Replies: 9
Views: 629
Posted By briphaeton
Re: 1928 60-A 2-Window Fordor Sedan "air vents"......

The cowl vent on the 60-A was used for 4 months according to Marco.
https://web.archive.org/web/20190213081853/http://www.abarnyard.com/corral/60a-1.htm
Showing results 1 to 25 of 239

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:47 AM.